manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Honeywell AUTOMATIC CONTROL Engineering Manual is an essential resource for professionals seeking in-depth knowledge on control systems. This comprehensive manual covers various aspects of automatic control, providing valuable insights and practical guidance. Download your free copy exclusively from manualshive.com, the go-to hub for user manuals.

Share
Download
background image

ENGINEERING MANULA OF AUTOMATIC CONTROL

INDIVIDUAL ROOM CONTROL APPLICATIONS

413

RADIANT PANELS

A radiant panel is a surface that transfers 50 percent or more

of its temperature to other surfaces by radiation. Radiant panels
may be used for heating or cooling of individual spaces, or
may be used in conjunction with central fan systems. The panel
can be in a floor, wall, or ceiling, and the surface temperature
can be maintained by electrical heating elements or by
circulating water or steam.

Control for radiant panel heating or cooling can be difficult.

Conventional space control with a thermostat may not be
appropriate because it is difficult, if not impossible, to locate
the thermostat to sense the radiant heat. Because radiant heat
does not heat the air, the thermostat must either see the radiant
heat or sense the space temperature change caused by the
radiation warming the furniture and occupants in the space.
The time lag in the second instance is too long for accurate
control. Figure 13 shows a hot water radiant floor heating panel
with an outdoor reset control system.

Fig. 13. Radiant Floor Heat System

with Outdoor Reset Control.

The space sensor, reset from the outdoor temperature, controls

the valve. As hot water circulates through the panel, heat radiates
to warm objects in the space and space temperature rises. The
space sensor senses the increase in space temperature and
signals the controller to reposition the valve. The outdoor air
sensor provides a reset schedule to raise the controller setpoint
as the outdoor temperature decreases. To prevent tiles from
softening and concrete from cracking, radiant floor panel surface
temperatures should not exceed 85F. Where hot water
temperatures may exceed 85F, the high-limit sensor resets
circulating water temperature.

Wall panels and ceiling panels can be controlled directly by

a room thermostat. Surface temperatures should not exceed
100F for wall panels and 120F for ceiling panels. (The actual
hot water temperature may be higher.)

Radiant heat panels that use electric resistance heating

elements are controlled by a two-position thermostat. As the
space temperature drops below the thermostat setpoint and
differential, the thermostat closes a switch to allow current flow
to heat the elements.

When a radiant panel is used for cooling, the temperature of

the water circulating through the panel must be at least 1

°

F

above the dew point temperature of the space to prevent
condensation on the panel.

A radiant panel may be used for both heating and cooling, as

shown in Figure 14. A heating/cooling panel uses a four-pipe
system regulated by two-way valves on both supply and return.
A call for heat at the thermostat closes the chilled water supply
and return ports and modulates hot water supply and return. A
call for cooling closes the hot water supply and return ports
and modulates chilled water supply and return.

SPACE
TEMPERATURE
SENSOR

RADIANT PANEL

C3019

PUMP

OUTDOOR AIR

TEMPERATURE

SENSOR

THREE-WAY

MIXING

VALVE

CONTROLLER

HIGH-LIMIT
SENSOR

BOILER

Fig. 14. Heating/Cooling Radiant Panel.

Constant-volume, constant-temperature central fan systems

can be combined with radiant-panel heating or cooling to satisfy
ventilation requirements. Occupancy schedules determine fan
operation. Room thermostats control the radiant panels to
maintain space temperature. Load anticipation is necessary
because of the high thermal inertia of this system. In general,
the thermostat setting should not be changed because of thermal
lag and the possibility of overshoot. Thermal lag in some radiant
floors can be several hours or more.

UNIT HEATERS

GENERAL

Unit heaters provide space heating for large open areas such

as building entrances, garages, workshops, warehouses, and
factories. Unit heaters are typically hung from the ceiling,
although cabinet versions are available. A fan forces air across
a coil containing hot water, steam, a warm-air heat exchanger,
or electric resistance elements. Warm-air units may be gas or
oil fired.

THERMOSTAT

RADIANT PANEL

C3020

CHILLED
WATER
SUPPLY

CHILLED
WATER
RETURN

HOT WATER

SUPPLY

HOT WATER

RETURN

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AUTOMATIC CONTROL

FAAC 740 D Manual preview
740 D
Brand: FAAC Pages: 14
Eaton SC100 Operation Handbook preview
SC100
Brand: Eaton Pages: 86
GARAN EWS-102 Calibration & Setup preview
EWS-102
Brand: GARAN Pages: 8
Gamma Vacuum SPCe User Manual preview
SPCe
Brand: Gamma Vacuum Pages: 25
Gamma DIGITEL MPCq User Manual preview
DIGITEL MPCq
Brand: Gamma Pages: 28
hager coviva Smartbox TKP100A Quick Manual preview
coviva Smartbox TKP100A
Brand: hager Pages: 4
Vag ZETA Operating And Maintenance Instructions Manual preview
ZETA
Brand: Vag Pages: 12
Hanwell MS1000 Installation Manual preview
MS1000
Brand: Hanwell Pages: 34
HANSONG BM240 User Manual preview
BM240
Brand: HANSONG Pages: 11
Datapath HX4 Quick Start Manual preview
HX4
Brand: Datapath Pages: 12
Hansen HS6 Specifications, Applications, Service Instructions & Parts preview
HS6
Brand: Hansen Pages: 4
York MILLENNIUM Manual preview
MILLENNIUM
Brand: York Pages: 20
Watts 709 Series Instruction, Installation, Maintenance And Repair Manual preview
709 Series
Brand: Watts Pages: 4
WaterCop SmartConnect Owner'S Manual preview
SmartConnect
Brand: WaterCop Pages: 4
GBD BE24G Installation Instructions Manual preview
BE24G
Brand: GBD Pages: 60
Zapf Creation Baby Born 828656 Manual preview
Baby Born 828656
Brand: Zapf Creation Pages: 2
Mazurczak MTR 3000 Installation And Operating Instructions Manual preview
MTR 3000
Brand: Mazurczak Pages: 9
GiBiDi GECO LUX GECO60 Instructions For Installations preview
GECO LUX GECO60
Brand: GiBiDi Pages: 48

Brands by name

Popular brands

Load more brands