manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Share
Download
Honeywell AUTOMATIC CONTROL Engineering Manual Download Page 427

ENGINEERING MANULA OF AUTOMATIC CONTROL

INDIVIDUAL ROOM CONTROL APPLICATIONS

417

Fig. 23. Unit Ventilator in Standby/Warm-up Stage.

CYCLE I–FIXED MAXIMUM PERCENTAGE OF OUTDOOR AIR

When the space is warmed to the low end of the thermostat

throttling range, Cycle I begins. As shown in Figure 24, control
components are the room thermostat, heating coil valve, damper,
and modulating low-limit controller. The outdoor air damper
and heating coil valve operate in sequence in accordance with
the demand of the thermostat. The heating valve is full open.
As space temperature rises, the thermostat modulates the
damper to its maximum open position. The fixed maximum
position is normally 100 percent open. As space temperature
continues to rise, and after the damper moves to its maximum
position, the heating coil valve modulates closed. If a cooling
coil is installed in the unit, the cooling coil valve opens as space
temperature rises further. The low limit controller is necessary
to prevent freezing conditions that occur when occupants lower
the room control setpoint when it is below freezing outside,
plus it prevents the discomfort that would result in discharging
air into the room below 55 degrees F.

Fig. 24. Unit Ventilator Cycle I Control.

CYCLE II–FIXED MINIMUM PERCENTAGE OF OUTDOOR AIR

Cycle II control (Fig. 25) provides a fixed minimum

percentage of outdoor air (usually 10 to 33 percent, adjustable
from 0 to 100 percent).

At low space temperatures, the outdoor air damper is closed

and the heating coil valve and face damper are full open. As
space temperature rises, the outdoor air damper moves to its
minimum position. On a further rise in space temperature, the
face damper modulates closed, and on a further rise in space
temperature, the coil valve closes. When the space temperature
is at setpoint, the valve is full closed. As space temperature
rises above setpoint, the outdoor and return air dampers
modulate to 100 percent outdoor air at the top of the throttling
range. The low-limit controller can limit the closure of the coil
valve, face damper, and the opening of the outdoor air damper
to prevent the discharge air temperature from dropping below
its setpoint.

C3040

CONVECTION
AIR

OUTDOOR
AIR

OA, RA
DAMPERS

OPEN

CLOSED

RETURN
AIR

FILTER

HEATING

COIL

VALVE

FAN

FAN
INTERLOCK

THERMOSTAT

DAMPER
ACTUATOR

C3029

DISCHARGE 
AIR

OUTDOOR
AIR

OPEN

OA, RA
DAMPERS

RETURN
AIR

FILTER

HEATING

COIL

VALVE

FAN

FAN
INTERLOCK

LOW-LIMIT
TEMPERATURE
CONTROLLER

THERMOSTAT

DAMPER
ACTUATOR

OPERATION CYCLE

HEATING
VALVE

OUTDOOR

AIR

DAMPER

FINAL
CONTROL
ELEMENT
POSITION

CLOSED

LOW

SPACE TEMPERATURE

HIGH

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands