manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Share
Download
Honeywell AUTOMATIC CONTROL Engineering Manual Download Page 237

ENGINEERING CMANUAL OF AUTOMATION CONTROL

AIR HANDLING SYSTEM CONTROL APPLICATIONS

227

FEATURES

1. A motorized zone mixing damper and space temperature

PID control loop for each zone provides zone control.

2. A single coil or group of coils in the hot deck furnishes

heat for the entire system.

3. The hot deck temperature is reset by the zone with greatest

load which provides efficient control when used in
conjunction with a cold deck coil/control.

4. A reasonably constant volume of air is delivered to each

room or zone.

5. A dynamic sequence-of-operation graphic display. This

not only clearly explains the sequence but also allows
easy program modification.

NOTE: Except for low-leakage OA dampers, measurable

leakage usually exists through “closed” dampers.
Given this leakage, as the zone heat demand increases
from zero to 15%, the hot deck temperature setpoint
is raised from the mixed air temperature to 80

°

F before

any zone damper movement. Zone heating demand
from 15 to 50% then modulates the zone dampers from
zero to 100% open to the 80

°

F hot deck. Further zone

heating demand from 50 to 100% raises the hot deck
temperature setpoint from 80

°

F to the upper limit of

105

°

F. A major objective of this strategy is to minimize

heat leakage to zones requiring no heat.

CONDITIONS FOR SUCCESSFUL OPERATION

1. A hot water coil on units having full flow at all times

provides uniform hot deck temperatures. This can be
accomplished with a three-way valve and coil pump.
Resetting hot water temperature also helps.

2. All zones are connected to load the reset program to

satisfy total load requirements. In large systems good
practice dictates connecting only selected diverse zone
loads. Zones that may be allowed to go out of control
(storage rooms, etc.) should not be connected to the load
reset program.

3. Each zone duct should have a balancing damper following

the mixing dampers to ensure design volume to each zone.

NOTE: See the Microprocessor-Based/DDC

Fundamentals section for a description of the
load reset program.

LIMITATIONS

1. If only selected zones are connected to the load reset

program, the load requirements of unconnected zones
may not be satisfied.

2. Reduced steam flow may cause temperature gradients

across the face of the coil.

SPECIFICATIONS

See FAN SYSTEM START-STOP CONTROL.

Anytime the supply fan runs, heating control shall be enabled.

Each zone mixing damper shall be modulated to maintain

zone space temperature setpoint. The hot water valve shall be
modulated to maintain the hot deck temperature setpoint.

The hot deck temperature setpoint shall be reset from the

MA temperature to 80

°

F as the heating demand from the zone

with the greatest heating demand varies from 0 to 15%.

Zone mixing dampers shall modulate from 0 to 100% open

to the hot deck as their respective zone demands for heating
vary from 15 to 55%.

The hot deck temperature setpoint shall be reset from 80

°

F

to 105 

°

F as the heating demand from the zone with the greatest

heating demand varies from 55 to 100%.

PSYCHROMETRIC ASPECTS

In the following chart it is assumed that:

1. MA temperature is 55

°

F DB.

2. The zone with the greatest heating load requires a hot

deck temperature of 90

°

F DB.

3. The zone depicted requires 75

°

F DB SA to meet its load.

C2551-1

75

°

F DB

SA FROM MIXING 
DAMPER TO ZONE

HOT DECK
90

°

F DB

1

MA
55

°

F DB

Item

No.

Explanation

1

Heating of MA to the hot deck temperature
occurs along a line of constant moisture
content. Individual zones obtain any needed SA
temperature along this line with the coldest
zone controlling the hot deck temperature and
getting 100 percent hot deck air.

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands