manualshive.com logo in svg

Honeywell AUTOMATIC CONTROL, Engineering Manual

Share
Download
Honeywell AUTOMATIC CONTROL Engineering Manual Download Page 335

ENGINEERING MANUAL OF AUTOMATIC CONTROL

CHILLER, BOILER, AND DISTRIBUTION SYSTEM CONTROL APPLICATIONS

325

CHILLER HEAT RECOVERY SYSTEM

A chiller heat recovery system uses heat rejected from a chiller

to satisfy a simultaneous heating load. To accomplish this the
heating water design temperature becomes the condenser water
design temperature for the chiller. A typical simultaneous cooling
and heating load includes an interior zone cooling load and a
perimeter zone heating load. When the cooling load is greater
than the heating load, the excess heat is dissipated in a cooling
tower. The control strategy is to use as much heat as needed from
the condenser and to reject excess heat to the cooling tower when
necessary.

Figure 32 shows a heat recovery system and control sequence

for a cooling system with one chiller and a double bundle
condenser where chiller capacity is controlled from the chilled
water supply temperature. The double bundle condenser uses heat
recovery water or cooling tower water or both to cool refrigerant.
Cooling tower water cannot be mixed with heat recovery water
so the two systems must be isolated. In a single chiller system,
the control system checks the water temperature coming out of
the heat recovery bundles (T3). If it is warmer than the water
returning from the heating loads (T2), valve V1 opens to circulate
condenser water through the system. A hot water generator (boiler
or converter) provides additional heat as required. If the heat
recovery system is not cooling the condenser sufficiently, the
cooling tower is used to dissipate excess heat. In multiple chiller
systems, the heat recovery chiller is controlled by the heating
load (T1). The other chillers provide additional cooling as required.

Fig. 32. Heat Pump Cycle Controls and Sequence.

COOLING

TOWER

FOR MULTIPLE CHILLERS 
THIS IS REPLACED 
BY CAPACITY 
CONTROL OF HEAT 
REJECTION CHILLER

C2696

TEMPERATURE

AT T1 (

°

F)

110

105

100

95

ACTION

OFF

IF T3 > T2, 
THEN T1 CONTROLS V1
(CONDENSER HEAT)

ON

OPEN

OA DAMPER
COOLING

CLOSED

CLOSED

V2 CONTROLLED
BY T1

OPEN

FOR MULTIPLE CHILLERS
THIS IS REPLACED BY 
CAPACITY CONTROL OF 
HEAT REJECTION CHILLER

SHUT OFF OA
COOLING ON
FAN UNITS

HEAT 
SOURCE

T1

LOAD

HOT WATER
GENERATOR

V2

V1

T2

T3

REFRIGERANT CIRCUIT
(REMOVING HEAT FROM
INTERIOR ZONES)

DOUBLE
BUNDLE
CONDENSER

T

If chilled water reset is used, stop the reset action when the

cooling tower is off. This provides recovery system heat to a lower
outdoor temperature before it is necessary to use fuel for heating.

FREE COOLING-TOWER COOLING

When the condenser water temperature from an evaporative

cooling tower is equal to or lower than chilled water load
requirements, mechanical refrigeration is not needed. During
these times “free cooling” from the evaporative cooling tower
is available without having to supply energy to the compressor.
Figures 33, 34, and 35 show three methods of providing tower
cooling to the chilled water circuit.

In refrigerant vapor migration (Fig. 33) two refrigerant paths

with migration valves are added between the condenser and
the evaporator. The paths bypass the compressor and allow
gravity flow of liquid refrigerant from condenser to evaporator
and vapor flow from evaporator to condenser. Refrigerant
vaporizes in the evaporator and migrates to the condenser where
it is condensed by cooling tower water. The liquid then flows
back to the evaporator by gravity. The chiller must be designed
so the flow paths are unrestricted and the evaporator is lower
than the condenser. The bypass valves are normally included
as a chiller package option by the manufacturer.

Fig. 33. Free Cooling Using

Refrigerant Vapor Migration.

CONDENSER

COMPRESSOR

EVAPORATOR

LOAD

CHILLED
WATER
PUMP

REFRIGERANT
MIGRATION
VALVES

CONDENSER
WATER
PUMP

COOLING
TOWER

TOWER
HEATER
(OPTIONAL)

C2697

Summary of Contents for AUTOMATIC CONTROL







































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands