GEA Omni Page 96 Instruction Manual Download | Manualshive

Page: 96 / 238

background image

2.14.2

Sensors Tab

fig.97:

Sensors tab display

This tab is used to adjust the range of sensors monitored by the panel. The table is divided into nine columns.
The leftmost column contains an icon that indicates whether the chosen point is an input or output. A green
arrow pointing to the right indicates that the point is an input, and a blue arrow pointing to the left indicates that
the point is an output. The remaining channels are detailed below.

1.

Channel

The text in this column indicates the slice number and channel that the chosen point occupies in the I/O sys-
tem.

2.

Description

This column contains the name of the chosen point.

3.

Min

This column contains the lowest allowable value for the chosen point during normal panel operation.

4.

Measured

This column contains the calibrated value read from or transmitted to the chosen point.

5.

Max

This column contains the highest allowable value for the chosen point during normal panel operation.

6.

Raw Scaled

This column contains the

Raw Signal

received by associated sensor scaled between the selected minimum

and maximum values.

7.

Offset

This column contains the value that is added to the reading displayed in the

Raw Scaled

column to obtain

the measured value for the sensor.

8.

Raw Signal

This column contains the unscaled value received by the sensor.

User interface
Configuration

Instruction Manual | GEA Omni™

Control panel

96

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
94
95
96
97
98
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Parker Pages: 30

Brand: VAT Pages: 22

Brand: Zetkama Pages: 6

Brand: Facility Explorer Pages: 4

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 42

Brand: D+H Pages: 36

Brand: D-Box Pages: 4

Brand: D+H Pages: 36

Brand: dbx Pages: 52

Brand: Hankscraft Runxin Pages: 58

Brand: J3C Pages: 2

Brand: Zamel Pages: 2

FAREX SR MINI SYSTEM

Brand: RKC INSTRUMENT Pages: 82

Brand: Harman Pages: 20

Brand: Netro Pages: 14

Brand: Ezodo Pages: 7

Brand: Gecko Pages: 82

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands