GEA Omni Instruction Manual Download | Manualshive

Page: 216 / 238

background image

Warning

Explanation

Illegal Oil Filter Differential
Pressure Warning

This annunciation will be triggered if the calculated value of the

Oil Filter Dif-

ferential

falls below -2 PSID.

Oil Pump Loss of Interlock Aux-
iliary 1 Warning

This annunciation will be triggered if the interlock input of the lead oil pump in
a dual pump system becomes de-energized while the pump is supposed to
be running. This annunciation will only be enabled if the compressor is con-
figured with dual oil pumps, and the first pump is selected as the lead pump.
An annunciation will cause the lag pump to start.

Oil Pump Loss of Interlock Aux-
iliary 2 Warning

This annunciation will be triggered if the interlock input of the lead oil pump in
a dual pump system becomes de-energized while the pump is supposed to
be running. This annunciation will only be enabled if the compressor is con-
figured with dual oil pumps, and the second pump is selected as the lead
pump. An annunciation will cause the lag pump to start.

Low Suction Pressure Warning

This annunciation will be triggered if the compressor suction pressure
exceeds the value obtained by subtracting the

Low Suction Pressure Warn-

ing Offset’

parameter from the

Low Suction Pressure Shutdown

parameter.

High Inlet Temperature Warn-
ing

This annunciation will be triggered if the inlet temperature reading exceeds
the value of the

High Inlet Temperature Warning

parameter.

Low Inlet Temperature Warning This annunciation will be triggered if the inlet temperature reading falls below

the value of the

Low Inlet Temperature Warning

parameter.

High Outlet Temperature Warn-
ing

This annunciation will be triggered if the outlet temperature reading exceeds
the value of the

High Outlet Temperature Warning

parameter.

Low Outlet Temperature Warn-
ing

This annunciation will be triggered if the outlet temperature reading falls
below the value of the

Low Outlet Temperature Warning

parameter.

High Oil Differential Pressure
Warning

This annunciation will be triggered if the calculated oil differential pressure
exceeds the value obtained by subtracting the

High Oil Differential Pressure

Warning Offset

parameter from the

High Oil Differential Pressure Shutdown

parameter.

Low Oil Differential Pressure
Warning

This annunciation will be triggered if the calculated oil differential pressure
falls below the value obtained by adding the

Low Oil Differential Pressure

Warning Offset

parameter to the

Low Oil Differential Pressure Shutdown

parameter.

Annunciations
Warnings

Instruction Manual | GEA Omni™

Control panel

216

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
214
215
216
217
218
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

FEPL-02 Ethernet POWERLINK

Brand: ABB Pages: 2

Brand: ABB Pages: 2

Brand: Lawler Pages: 5

Brand: Waterway Pages: 16

Brand: Kasco Pages: 3

Brand: Gardigo Pages: 8

Brand: Gardigo Pages: 19

Brand: NAPCO Pages: 48

Magnum Alert 2600

Brand: NAPCO Pages: 68

Brand: Sanhua Pages: 3

Brand: QED Pages: 26

Brand: Watts Pages: 17

Brand: Allen-Bradley Pages: 16

Brand: D+H Pages: 2

1020 CAN-RS232-RS422 MFL

Brand: PENKO Pages: 29

Brand: bluelab Pages: 39

Brand: SOMFY Pages: 2

Brand: Hard Head Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands