manualshive.com logo in svg

GEA Omni, Instruction Manual

Share
Download
GEA Omni Instruction Manual Download Page 142

2.

High Discharge Pressure Booster Shutdown

This parameter is used to select the suction pressure value above which a 

High Discharge Pressure Shut-

down

 will be annunciated. The parameter will only appear if the compressor application is set to 

Swing

 in the

configuration. The shutdown will only be issued if the compressor currently operating as a booster. The
value is measured in the panel pressure units as selected on the 

Panel Settings

 screen.

3.

High Discharge Pressure High Stage Shutdown

This parameter is used to select the suction pressure value above which a 

High Discharge Pressure Shut-

down

 will be annunciated. The parameter will only appear if the compressor application is set to 

Swing

 in the

configuration. The shutdown will only be issued if the compressor currently operating as a high stage. The
value is measured in the panel pressure units as selected on the 

Panel Settings

 screen.

4.

High Discharge Pressure Warning Offset

This parameter is used to set an offset value subtracted from the 

High Discharge Pressure Shutdown

parameter. If the discharge pressure exceeds this calculated value, a 

High Discharge Pressure Warning

 will

be annunciated. The value is measured in the panel pressure units as selected on the 

Panel Settings

screen.

5.

Limitation Discharge Pressure Load Inhibit Offset

This parameter is used to set an offset value subtracted from the 

Low Discharge Pressure Shutdown

 param-

eter. If the discharge pressure rises above this calculated value, the compressor will be prevented from load-
ing. The value is measured in the panel pressure units as selected on the 

Panel Settings

 screen.

6.

Limitation Discharge Pressure Force Unload Offset

This parameter is used to set an offset value subtracted from the 

Low Discharge Pressure Shutdown

 param-

eter. If the discharge pressure rises above this calculated value, the compressor will be forced to unload.
The value is measured in the panel pressure units as selected on the 

Panel Settings

 screen.

3.1.18

Discharge Temperature

Parameter

Units

Minimum

Maximum

Default

High Discharge Temperature Shut-
down

°C

1.0 °C

200.0 °C

100.0 °C

°F

33.8 °F

392.0 °F

212.0 °F

High Discharge Temperature Warn-
ing Offset

Kelvin

0.0 K

50.0 K

4.4 K

F°

0.0 F°

90.0 F°

8.0 F°

1.

High Discharge Temperature Shutdown

This parameter is used to select the discharge temperature value above which a 

High Discharge Tempera-

ture Shutdown

 will be annunciated. The shutdown will only be issued if the compressor is running. The value

is measured in the panel temperature units as selected on the 

Panel Settings

 screen.

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

142

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands