GEA Omni Instruction Manual Download

Page: 129 / 238

High Oil Differential Pressure Starting Shutdown Timer

This parameter is used to select the period of time that the

Oil Differential Pressure

may exceed the

High Oil

Differential Pressure Shutdown

parameter while the compressor is starting before a

High Oil Differential

Pressure Shutdown

is annunciated. The default value of this parameter is dependent on the compressor

manufacturer. This parameter is fixed on Grasso compressors and will not be visible. The value is measured
in seconds.

High Oil Differential Pressure Running Shutdown Timer

This parameter is used to select the period of time that the

Oil Differential Pressure

may exceed the

High Oil

Differential Pressure Shutdown

parameter while the compressor is running before a

High Oil Differential

Pressure Shutdown

is annunciated. The default value of this parameter is dependent on the compressor

manufacturer. This parameter is fixed on Grasso compressors and will not be visible. The value is measured
in seconds.

High Oil Differential Pressure Warning Offset

This parameter is used to set an offset value subtracted from the

High Oil Differential Pressure Shutdown

value. If the differential exceeds this calculated value, a

High Oil Differential Pressure Warning

will be annun-

ciated. The value is measured in the panel pressure units as selected on the

Panel Settings

screen.

High Oil Differential Pressure Warning Timer

This parameter is used to select the period of time for which the

Oil Differential Pressure

may exceed the

calculated value for the

High Oil Differential Pressure Warning

before a

High Oil Differential Pressure Warn-

ing

is annunciated. The default value of this parameter is dependent on the compressor manufacturer. This

parameter is fixed on Grasso compressors and will not be visible. The value is measured in seconds.

Low Oil Differential Pressure Shutdown

This parameter is used to select the minimum allowable differential in oil pressure. If the differential falls
below this value, a

Low Oil Differential Pressure Shutdown

will be annunciated. The default value of this

parameter is dependent on the compressor manufacturer. The value is measured in the panel pressure units
as selected on the

Panel Settings

screen.

Low Oil Differential Pressure Starting Shutdown Timer

This parameter is used to select the period of time that the

Oil Differential Pressure

may fall below the

Low

Oil Differential Pressure Shutdown

parameter while the compressor is starting before a

Low Oil Differential

Pressure Shutdown

is annunciated. The default value of this parameter is dependent on the compressor

manufacturer. This parameter is fixed on Grasso compressors and will not be visible. The value is measured
in seconds.

Low Oil Differential Pressure Running Shutdown Timer

This parameter is used to select the period of time that the

Oil Differential Pressure

may fall below the

Low

Oil Differential Pressure Shutdown

parameter while the compressor is running before a

Low Oil Differential

Pressure Shutdown’

is annunciated. The default value of this parameter is dependent on the compressor

manufacturer. This parameter is fixed on Grasso compressors and will not be visible. The value is measured
in seconds.

Low Oil Differential Pressure Warning Offset

This parameter is used to set an offset value added to the

Low Oil Differential Pressure Shutdown

value. If

the differential falls below this calculated value, a

Low Oil Differential Pressure Warning

will be annunciated.

The value is measured in the panel pressure units as selected on the

Panel Settings

screen.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

129

Summary of Contents for Omni















































































































































































































































Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands

GEA Omni, Instruction Manual

Search results

Summary of Contents for Omni

Reviews:

Related manuals for Omni

Brands by name

Popular brands