GEA Omni Instruction Manual Download | Manualshive

Page: 173 / 238

background image

2.

Liquid Feed

•

Set Point

This parameter is used to choose the desired value at which the panel will attempt to maintain the liquid
level. The value is measured in percent.

•

Proportional Term

This parameter is used to set the proportional gain for PI control of the device. This value is multiplied by
the total error between the actual and desired values. The value is unitless.

•

Integral Term

This parameter is used to set the rate at which the PI controller will change its integral gain based on the
calculated error over time. The value is measured in samples per Repeat (s/R).

•

Dead Band

This parameter is used to define a range above and below the Set Point within which no action will be
taken to adjust the liquid level. The value is measured in percent.

•

Maximum Level

This parameter is used to select the Maximum Level. If the liquid level is higher a delay time will be
started to trigger a warning or shutdown. The value is measured in percent.

•

High Level Warning Delay (Liquid Feed Maximum Level Warning Delay)

This parameter is used to select the period of time for which a Maximum Level condition must persist
before a Max Liquid Level Warning condition will be annunciated. The value is measured in seconds.

•

High Level Shutdown Delay (Liquid Feed Maximum Level Shutdown Delay)

This parameter is used to select the period of time for which a Maximum Level condition must persist
before a Max Liquid Level Shutdown condition will be annunciated. The value is measured in seconds.

Instruction Manual | GEA Omni™
Control panel

Control

Evaporator Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

173

«
...
171
172
173
174
175
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Vacon Pages: 64

Brand: Kasco Pages: 3

ESD-5550 Series

Brand: GAC Pages: 12

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: Trane Pages: 72

SAE 07.2 Series

Brand: AUMA Pages: 116

SaunaLogic SL2 Control

Brand: Finnleo Pages: 14

Brand: Wenglor Pages: 44

Brand: Intermatic Pages: 3

Brand: Belimo Pages: 9

Brand: FMS Pages: 9

Brand: SIEB & MEYER Pages: 119

TITAN-TRACKSIDE-6

Brand: RC System Pages: 4

Brand: END ARMATUREN Pages: 32

Brand: Nice Pages: 40

Network Device NXC-8160s

Brand: ZyXEL Communications Pages: 67

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands