GEA Omni Instruction Manual Download | Manualshive

Page: 55 / 238

background image

4.

Arrow buttons

These buttons may be used to navigate between all compressor devices.

Touching the

Main

tab displayed at the top of the screen will bring up the display corresponding to the most

recently selected tile. If no tile has been previously selected in the

Overview

tab, the panel will bring up the infor-

mation of the compressor sequencer by default.

2.8.3

Schedule Tab

fig.52:

Sequencer Schedule Tab

This screen is used to display and modify the control behavior of the compressor sequencer. The main portion of
the display contains the control schedule, which is displayed in table format with each compressor device
assigned to a column and each row corresponding to a different step. The sequencer supports up to fifty steps.
The components of the display are:

1.

Current Level

This section contains the user defined name for the currently selected level, the target set point and
the current level status.

2.

Control value

This section displays the current control value of the level.

3.

Hide/ show timers

This button controls whether or not the three initial columns of the schedule table, containing the
time delays used while the sequencer is running automatically, are displayed.

4.

Level Selection

This drop down list is used to select which level is currently displayed.

Instruction Manual | GEA Omni™
Control panel

User interface

Sequencer

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

55

«
...
53
54
55
56
57
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Eaton Pages: 50

Brand: C&K systems Pages: 2

Brand: 1Control Pages: 8

Brand: Yardney Pages: 8

Brand: Rane Pages: 2

Brand: Harman Pages: 2

Brand: T-Link Pages: 3

Brand: OMC Pages: 18

Brand: Paradox Pages: 2

Brand: Paradox Pages: 2

FrameSaver 9120

Brand: Paradyne Pages: 20

VeriSafe VS2-NET

Brand: Panduit Pages: 6

Brand: T&S Pages: 5

Brand: Watts Pages: 4

Brand: Fingertips Lab Pages: 15

Brand: WABCO Pages: 4

Brand: Rayrun Pages: 4

Brand: Parker Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands