GEA Omni Instruction Manual Download | Manualshive

Page: 53 / 238

background image

4.

Compressor selection

This drop down list is used to select the number of the compressor. The options are dependent on the type
of panel affiliated with the compressor.

5.

Level

This drop down list is used to select which of the available control levels the compressor will be sequenced
on. Any level that is currently enabled will appear in the options.

6.

Unit ID

This drop down list is used to select the Modbus ID of the panel. This option will only be used if the
sequencer utilizes an Ethernet to Serial communication convertor.

7.

Device tag

This drop down list is used to select the name that will be associated with the compressor.

Clicking any tile will open the main tab for the compressor sequencer as detailed in Section 2.8.2, Page 53.

2.8.2

Main tab

This screen is used to display the current status and control parameters of the compressor sequencer and indi-
vidual devices. The display will change depending on whether it is currently showing the status of a control level
or a specific compressor.
When a control level tile is touched, the main tab will display the screen shown below:

fig.50:

Main sequencer tab (Control level)

1.

Control level information

This tile displays the current status, set point, current step and control value of the control level.

2.

Level enabled

This switch is used to toggle whether or not compressors on the selected level are currently permitted to be
sequenced.

Instruction Manual | GEA Omni™
Control panel

User interface

Sequencer

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

53

«
...
51
52
53
54
55
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: K&K Pages: 6

Brand: Mackie Pages: 16

Brand: TANDBERG Pages: 47

Brand: Dakota Digital Pages: 12

PDS CONTROL Series

Brand: S&P Pages: 32

Brand: LOGICDATA Pages: 23

Brand: Sunlover Pages: 2

Brand: Daikin Pages: 32

Brand: Kelly Pages: 32

Brand: Eazyzap Pages: 32

Brand: Current Pages: 4

Brand: PEAS Pages: 4

Brand: Sollae Systems Pages: 72

Dynamic Boiler Controller

Brand: Intiel Pages: 25

SR-ZV9002T4-CCT-RU

Brand: Z-Wave Alliance Pages: 10

Brand: Paradox Pages: 38

Brand: Phychips Pages: 14

Brand: IQRF Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands