GEA Omni Instruction Manual Download | Manualshive

Page: 67 / 238

background image

1.

Viewable Grid Area

From here, the user can view the annunciation table. The table is divided into seven columns as detailed
below.

•

Type

The graphic displayed here is determined by the type of the triggered annunciations. Red indicates shut-
down, yellow indicates warning and blue indicates a notification.

•

Description

Displays the name of the annunciation that was triggered.

•

Time

The time when the annunciation was either issued or cleared.

•

Parameter

The current value of the warning or shutdown set point which triggered the annunciation, where applica-
ble.

•

Action

The text displayed here indicates whether the annunciation was issued or cleared.

•

Clear

This column will be filled only if the action column displays

Cleared

. It indicates whether the annunciation

was cleared manually or automatically.

•

RT-Trend

When a shutdown or warning annunciation is issued, the last fifteen minutes of historical data is
recorded. The user may view this information by selecting the picture embedded into the grid’s cell.
These will not be generated during panel startup. Manual RT-Trend snapshots are also displayed in this
format and appear in the table as notifications.

Instruction Manual | GEA Omni™
Control panel

User interface

History

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

67

«
...
65
66
67
68
69
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: S&C Pages: 40

Brand: S&C Pages: 34

Brand: FAAC Pages: 14

Brand: Daikin Pages: 5

iBox Hub 25020180

Brand: Hans Grohe Pages: 36

Brand: Harpo Pages: 35

Brand: Hardi Pages: 2

Brand: jcm-tech Pages: 8

BT300 BurnerTronic

Brand: Lamtec Pages: 48

Brand: Madas Pages: 6

Brand: Madas Pages: 11

Brand: L-Acoustics Pages: 24

Brand: L-Acoustics Pages: 21

Brand: M&S Systems Pages: 4

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: Burlington Pages: 7

Brand: Hattersley Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands