GEA Omni Instruction Manual Download | Manualshive

Page: 36 / 238

background image

1.

Analysis Mode

This drop down list is used to select the vibration analysis method that will be used. The vibration analysis is
always carried out using a variant of the Fast Fourier Transform. The options are used to select whether an
envelope will be used in the analysis. The options are:

–

FFT

This option is used to select a normal Fast Fourier Transform.

–

H-FFT

This option is used to select a Fast Fourier Transform with an envelope.

2.

Units

This drop down list is used to select the units that will be used for measuring vibration. The options are:

–

inches/s

This option is used when vibration should be measured in terms of velocity.

–

mg

This option is used when vibration should be measured in terms of acceleration.

3.

Frequency

This drop down list is used to select the units that will be used for measuring frequency. The options are:

–

CPM

This option is used when frequency should be measured in Cycles per minute.

–

Hz

This option is used when frequency should be measured in Hertz.

2.5.4

Starter tab

fig.29:

Starter tab display

User interface
Compressor

Instruction Manual | GEA Omni™

Control panel

36

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
34
35
36
37
38
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Salda Pages: 16

Brand: Fingertips Lab Pages: 15

Brand: Fox Pages: 5

Pearldex Series

Brand: KaMo Pages: 2

Brand: Adaptec Pages: 2

Brand: Webasto Pages: 12

Brand: MERCATOR Pages: 4

Brand: W&T Pages: 217

Brand: Variotech Pages: 24

TOP-43 EE Series

Brand: CAME Pages: 2

Brand: WattMaster Pages: 104

Brand: FUTABA Pages: 6

Commander Site Controller

Brand: VeriFone Pages: 34

Brand: Avanza Pages: 10

Brand: VOSS Pages: 68

Brand: D+H Pages: 36

Infilex ZM WY5122

Brand: Azbil Pages: 12

Brand: AlfaRadio Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands