GEA Omni Instruction Manual Download | Manualshive

Page: 148 / 238

background image

1.

Power Failure Restart Mode

This parameter is used to select what action the compressor should take in the event of a power outage. The
options are:

•

Disabled

If this option is selected, the compressor will do nothing following a power outage.

•

Local

If this option is selected, the compressor will start in local mode following a power outage.

•

Remote

If this option is selected, the compressor will start in remote mode following a power outage.

•

Shutdown

If this option is selected, the compressor will annunciate a shutdown condition following a power outage.

2.

Power Failure Restart Delay

This parameter is used to select the period of time the panel will wait after recovering from a power outage
before taking the action dictated in the

Power Failure Restart Mode

parameter. This parameter will only be

visible if the

Power Failure Restart Mode

parameter is set to an option other than

Disabled

. The value is

measured in seconds.

3.

Power Failure Restart Abort Timer

This parameter is used to select the maximum period of time that a power failure may persist before the
power failure restart function will be disabled. If the duration of a power outage exceeds this time period, the
panel will take no action once power is restored, regardless of the action dictated in the

Panel Failure

Restart Mode

parameter. In this condition, a

Power Failure Restart Abort

shutdown condition will be annunci-

ated. This parameter will only be visible if the

Power Failure Restart Mode

parameter is set to an option

other than

Disabled

. The value is measured in minutes.

3.1.24

Superheat

Parameter

Units

Minimum

Maximum

Default

Superheat Suction
Annunciations

Selection – See Description

High Suction Superheat
Shutdown

Kelvin

0.0 K

100.0 K

100.0 K

°F

0.0 °F

180.0 °F

180.0 °F

High Suction Superheat
Shutdown Timer

Seconds

0 s

900 s

80 s

Low Suction Superheat
Shutdown

Kelvin

0.0 K

100.0 K

0.0 K

°F

0.0 °F

180.0 °F

0.0 °F

Control
Compressor Control Parameters

Instruction Manual | GEA Omni™

Control panel

148

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
146
147
148
149
150
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Garmin Pages: 12

Brand: VADDIO Pages: 2

Brand: Accel Pages: 8

Brand: Rane Pages: 2

Brand: Salda Pages: 16

Brand: Samson Pages: 32

Brand: Quantum Pages: 15

Brand: Quectel Pages: 95

Brand: ICAS Pages: 51

Brand: Icar Pages: 40

Brand: Icar Pages: 86

Brand: Icar Pages: 39

Brand: IBP Pages: 12

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: X Rocker Pages: 38

Brand: Elby Designs Pages: 4

Brand: Maximum Controls Pages: 58

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands