GEA Omni Instruction Manual Download | Manualshive

Page: 68 / 238

background image

2.10.5

Analysis Tab

The

Analysis

tab may be used to quickly identify common annunciations that have been generated by the panel.

It lists frequent shutdowns and warnings and the number of times each has occurred over a selected time range.

fig.67:

Analysis tab display

1.

Frequent Shutdowns

This section displays the five most common shutdowns that have occurred over the shown time period.
The information displayed here indicates the annunciation name and the total number of times it was
issued. It also calculates what percentage of the total number of shutdowns the annunciation in question
accounts for.

2.

Frequent Warnings

This section is similar in functionality to the

Frequent Shutdowns

section, displaying the same informa-

tion and analysis for warnings.

3.

Annunciations Graph

This area displays the distribution of shutdowns and warnings across the selected range. For each day,
the yellow bar indicates the total number of warnings that occurred and the red bar indicates the total
number of shutdowns.

4.

Date Range

The user can select between any of these preset time periods to change the date range. The

Date

Range

option is also available, which displays the entire period that the panel has been active.

User interface
History

Instruction Manual | GEA Omni™

Control panel

68

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
66
67
68
69
70
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Farfisa Pages: 20

Brand: Racal Instruments Pages: 64

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: Galaxy Control Systems Pages: 5

Brand: IDK Pages: 96

Brand: National Instruments Pages: 6

Brand: National Instruments Pages: 6

Brand: RADEMACHER Pages: 48

Brand: vacuubrand Pages: 12

Brand: Vacon Pages: 47

Brand: Vacon Pages: 40

Brand: ZPA Pecky, a.s. Pages: 36

Brand: Mitsubishi Pages: 16

Brand: SOMFY Pages: 4

Brand: MaintTech Pages: 28

Brand: Lauda Pages: 40

Turbo-V 250 series

Brand: Varian Pages: 79

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands