GEA Omni Instruction Manual Download | Manualshive

Page: 196 / 238

background image

fig.111:

Discharge options

1.

Discharge Pressure Scaling

This drop down list field contains a drop down list which is used to select the range of the discharge
pressure transducer.

2.

Discharge Pressure Max

This text box is used to select the maximum value that may be assigned to the discharge pressure
parameters of the compressor. The value is measured in PSIG.

3.

Discharge Temperature Max

This text box is used to select the maximum value that may be assigned to the discharge temperature
parameters of the compressor. The value is measured in degrees Fahrenheit.

Economizer Details

fig.112:

Economizer details options

1.

Economizer

This drop down list is used to select the type of economizer the package is equipped with, if one exists.

2.

Economizer Pressure

This drop down list is used to select the range of the economizer pressure sensor, if one exists.

3.

Economizer Temperature

This check box is used to select whether the economizer is equipped with a dedicated temperature sen-
sor.

Control
Configuration

Instruction Manual | GEA Omni™

Control panel

196

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
194
195
196
197
198
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: NEC Pages: 149

Brand: NEC Pages: 13

AirGENIO SUPERIOR

Brand: 2VV Pages: 27

Brand: Parker Pages: 28

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: WABCO Pages: 4

Brand: Rayrun Pages: 4

Brand: Parker Pages: 29

HydroTap G5 Touch-Free Wave

Brand: Zip Pages: 24

SYSMAC C500-NC222-E

Brand: Omron Pages: 164

Brand: IDEATEC Pages: 32

Brand: Broadcast Tools Pages: 15

Brand: Comparato Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands