GEA Omni Instruction Manual Download | Manualshive

Page: 121 / 238

background image

3.

High Motor Winding Shutdown

This parameter is used to select the temperature value in any motor winding phase above which a high tem-
perature shutdown condition will be annunciated. This parameter will only be visible if motor winding temper-
ature monitoring is selected in the

Motor Temperature Safeties

field motor section of the configuration. The

value is measured in the panel temperature units as selected on the

Panel Settings

screen.

4.

High Motor Winding Warning Offset

This parameter is used to set an offset value subtracted from the

High Motor Winding Shutdown

parameter.

If the temperature on either motor bearing exceeds this calculated value, a high temperature warning condi-
tion will be annunciated. This parameter will only be visible if motor winding temperature monitoring is
selected in the

Motor Temperature Safeties

field motor section of the configuration. The value is measured in

the panel temperature units as selected on the

Panel Settings

screen.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

121

«
...
119
120
121
122
123
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: OmarLift Pages: 14

Brand: Waterway Pages: 16

Brand: Dantherm Pages: 96

Brand: Valor Pages: 20

Brand: Samson Pages: 48

Brand: Lamtec Pages: 22

Brand: Rane Pages: 2

Brand: Yealink Pages: 8

Brand: Whale Pages: 8

Brand: Tascam Pages: 8

Brand: Telit Wireless Solutions Pages: 45

Brand: YOKOGAWA Pages: 33

Brand: Cooper Pages: 4

Brand: Trenz Electronic Pages: 21

Brand: Daikin Pages: 40

Brand: Carel Pages: 36

Brand: Handiquilter Pages: 53

Brand: Neets Control Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands