manualshive.com logo in svg

GEA Omni, Instruction Manual

Introducing the Instant Omni - your ultimate kitchen companion! Achieve culinary excellence effortlessly with its innovative features and user-friendly interface. Unlock the full potential of your Instant Omni by accessing the comprehensive User Manual for free. Download it now from manualshive.com, and master your culinary skills with ease.

Share
Download
background image

3.5.2

Fan Cycling

Parameter

Units

Minimum

Maximum

Default

Fan Cycling Enabled

Selection – See Description

Fan Cycling On Delay

Minutes

0.0 min

200.0 min

20.0 min

an Cycling Off Delay

Minutes

0.0 min

200.0 min

20.0 min

Fan Cycling Agitation Timer

Minutes

0.0 min

200.0 min

2.0 min

Set Point Delay While Agitating

Minutes

0.0 min

200.0 min

1.0 min

1.

Fan Cycling Enabled

This parameter is used to select how the zone fans will operate while the zone is satisfied. The options are:

•

Disabled
While this option is selected, the fan will run constantly while the zone is satisfied.

•

Enabled
While this potion is selected, the fans will run based on the fan cycling parameters described below.

2.

Fan Cycling On Delay

This parameter is used to select the period of time that the zone fans will remain off before beginning
cycling. The value is measured in minutes.

3.

Fan Cycling Off Delay

This parameter is used to select the period of time that the zone fans will continue to run after the zone tem-
perature falls below the lower edge of the dead band range. The value is measured in minutes.

4.

Fan Cycling Agitation Timer

This parameter is used to select the periods of time that the fans will run to circulate the air in the zone. After
this time period has elapsed, the fans will remain off for the same period of time before running again. The
value is measured in minutes.

5.

Set Point Delay While Agitating

This parameter is used to select the period of time that the zone temperature set points will be ignored while
the zone fans are running to circulate the air. The value is measured in minutes.

3.5.3

Defrost

Parameter

Units

Minimum

Maximum

Default

Liquid Solenoid Runtime Defrost

Selection – See Description

Liquid Solenoid Valve Runtime
Until Defrost

Minutes

0 min

32000 min

120 min

Instruction Manual | GEA Omni™
Control panel

Control

Evaporator Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

167

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

GE RSTi-EP User Manual preview
RSTi-EP
Brand: GE Pages: 425
YASKAWA P1000 Quick Start Manual preview
P1000
Brand: YASKAWA Pages: 256
ZETRON MAX Connection Manual preview
MAX
Brand: ZETRON Pages: 3
TCS Basys Controls QD Series Troubleshooting Worksheet preview
QD Series
Brand: TCS Basys Controls Pages: 2
Hans Grohe iBox Hub 25020180 Assembly Instruction And Instructions For Use preview
iBox Hub 25020180
Brand: Hans Grohe Pages: 36
IAI ROBO Cylinder RCP2 Series Quick Start Manual preview
ROBO Cylinder RCP2 Series
Brand: IAI Pages: 5
Vag CEREX 300-L Operation & Maintenance Instructions Manual preview
CEREX 300-L
Brand: Vag Pages: 15
GEA SIMATIC C7-623 Instruction Manual preview
SIMATIC C7-623
Brand: GEA Pages: 13
Black Horse Model BH33-B Instruction Manual Book preview
BH33-B
Brand: Black Horse Model Pages: 19
SILENTRON SERENYA 2000 Manual preview
SERENYA 2000
Brand: SILENTRON Pages: 20
MacroAir Technologies Controller 30 Operation Manual preview
Controller 30
Brand: MacroAir Technologies Pages: 32
Niko 350-20057 Manual preview
350-20057
Brand: Niko Pages: 28
Shaw ATLAS PVR User Manual preview
ATLAS PVR
Brand: Shaw Pages: 44
Washify MOXA Installing preview
MOXA
Brand: Washify Pages: 25
Allen-Bradley ControlLogix 1756-OX8I Installation Instructions Manual preview
ControlLogix 1756-OX8I
Brand: Allen-Bradley Pages: 20
microHAM micro2R User Manual preview
micro2R
Brand: microHAM Pages: 64
Texas Instruments TPSM8282xAEVM-127 User Manual preview
TPSM8282xAEVM-127
Brand: Texas Instruments Pages: 18
Zonet ZUH2215V Quick Installation Manual preview
ZUH2215V
Brand: Zonet Pages: 2

Brands by name

Popular brands

Load more brands