GEA Omni Instruction Manual Download | Manualshive

Page: 181 / 238

background image

Value

Description

Aux Warning #2

This input monitors a miscellaneous warning condition for the compressor. It will
be energized for normal panel operation. If this input ever becomes de-energized,
a warning annunciation will be triggered. The states are

On

or

Off

.

Compressor Motor Start

This output activates the starter for the compressor motor. It will energize when the
compressor is instructed to start, and will be de-energized at all other times. The
states are

On

or

Off

.

Oil Pump Motor Start

This output activates the starter for the oil pump motor. It will be energized when-
ever the oil pump is instructed to run, and will be de-energized at all other times.
The states are

On

or

Off

.

Load Solenoid

This output activates the compressor load solenoid. It will be energized whenever
the compressor is loading the solenoid, and will be de-energized at all other times.
The states are

On

or

Off

.

Unload Solenoid

This output activates the compressor unload solenoid. It will be energized when-
ever the compressor is unloading the solenoid, and will be de-energized at all
other times. The states are

On

or

Off

.

Shutdown Status

This output signalizes whether the panel has entered a shutdown state. It will be
energized for normal panel operation and will de-energize any time a shutdown
condition is annunciated. The states are

On

or

Off

.

Ready For Remote

This output signalizes whether the compressor is currently permitted to run via
external control from a remote device. It will be energized when remote mode is
permitted and disabled at all other times. The states are

On

or

Off

.

Oil Cooling

This output activates the oil cooing solenoid. It will be energized whenever the oil
cooling should be energized as determined by the type of oil cooling system, and
de-energized at any other time. The states are

On

or

Off

.

Unloaded Start

This output activates the solenoid of the compressor unload cycle. The states are

On

or

Off

.

Oil Separator Heater

This output activates the heater for the oil separator. It will be energized during
compressor standstill. The states are

On

or

Off

.

Warning Status

This output signalizes whether the panel has entered a warning state. It will be
energized for normal panel operation and will de-energize any time a warning con-
dition is annunciated. The states are

On

or

Off

.

Motor Start To Start Timer
Active

This output signalizes whether the motor start to start timer is currently active. It
will be energized while the timer is running and de-energized at all other times.
The states are

On

or

Off

.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Operating Data

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

181

«
...
179
180
181
182
183
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brand: Oceanic Systems Pages: 8

Brand: Rain Bird Pages: 24

ESP-LXIVM Series

Brand: Rain Bird Pages: 16

Brand: Rabe Pages: 61

Brand: Racal Instruments Pages: 35

Brand: Watts Pages: 4

Brand: Netro Pages: 14

Brand: Bard Pages: 102

Brand: Vestil Pages: 6

Brand: DirectConnect Pages: 2

CS ME-02 Series

Brand: pizzato Pages: 12

Brand: Lumel Pages: 32

Brand: jablotron Pages: 2

Brand: HIMA Pages: 40

Brand: Bartec Pages: 52

Integrated Controller Rev C EZ-ZONE PM

Brand: Watlow Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands