GEA Omni Instruction Manual Download | Manualshive

Page: 42 / 238

background image

2.6.3

Schedule tab

fig.36:

Condenser schedule tab

This screen is used to display and modify the condenser sequencer schedule. The main portion of the display
contains the currently selected control schedule, which is displayed in table format with each condenser device
assigned to a column and each row corresponding to a different step. The sequencer supports four independent
schedules, each containing up to fifty steps. The components of the display are:

1.

Schedule information

This section contains the user defined name for the currently selected schedule, the target set point
and the current condenser status.

2.

Control value

This section displays the current value of the condenser control value.

3.

Hide/ show timers

This button controls whether or not the three initial columns of the schedule table, containing the
time delays used while the sequencer is running automatically, are displayed.

4.

Schedule selection

This drop down list is used to select which schedule is currently displayed.

User interface
Condenser

Instruction Manual | GEA Omni™

Control panel

42

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

«
...
40
41
42
43
44
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Value Point Pages: 7

Brand: 3M Pages: 34

Brand: Danfoss Pages: 37

Brand: Daikin Pages: 44

Brand: Datavideo Pages: 8

Brand: Sanhua Pages: 3

Brand: National Instruments Pages: 102

Brand: NAU ROBOTICS Pages: 109

Maschine Mikro MK2

Brand: Native Instruments Pages: 181

Brand: YUGE Pages: 69

Brand: Quectel Pages: 232

Brand: Quectel Pages: 9

Brand: Quectel Pages: 73

Brand: Xilinx Pages: 2

Brand: IBM Pages: 214

Brand: STIEBEL ELTRON Pages: 44

Brand: Dejero Pages: 24

Brand: WINDY NATION Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands