GEA Omni Instruction Manual Download | Manualshive

Page: 119 / 238

background image

Parameter

Units

Minimum

Maximum

Default

rpm

See Description

High Motor Speed Shutdown

rpm

100 rpm

6000 rpm

3000 rpm

Low Motor Speed Shutdown

rpm

100 rpm

3000 rpm

1800 rpm

Motor Speed Maximum

rpm

100 rpm

6000 rpm

3600 rpm

Motor Speed Minimum

rpm

100 rpm

3000 rpm

1800 rpm

Motor Speed Start

rpm

100 rpm

3000 rpm

100 rpm

1.

Proportional Term

This parameter is used to set the proportional gain for PI control of the motor speed. This value is multiplied
by the total error between the current and desired speed values. This parameter is only visible if the configu-
ration indicates that the compressor uses a variable speed motor. The value is unitless.

2.

Integral Term

This parameter is used to set the rate at which the motor PI controller will change its integral gain base on
the calculated error over time. This parameter is only visible if the configuration indicates that the compres-
sor uses a variable speed motor. The value is measured in samples per Repeat (s/R).

3.

Mode

This parameter is used to select whether the motor PI controller will vary its output automatically or if it will
be controlled manually through the

Manual Mode Position

parameter. This parameter will only be visible if

the configuration indicates that the compressor uses a variable speed motor. The options are:

•

Auto

•

Percent

•

Motor Speed

4.

Manual Mode Position

This parameter is used to set the desired output of the PI controller while it is set to operate in manual mode.
This parameter will only appear if the

Mode

parameter is not set to

Auto

. The minimum, maximum and

default values will also change based on the currently selected option in the

Mode

parameter. If

Percent

is

selected, the range will be fixed as indicated in the table above and the value will be measured in percent. If

Motor Speed

is selected, the minimum value will be equal to the value of the

Motor Speed Minimum

parame-

ter, the maximum will be set to the value of the

Motor Speed Maximum

parameter, and the value will be

measured in rpm.

5.

High Motor Speed Shutdown

This parameter is used to set the motor speed value above which a

High Motor Speed Shutdown

will be

annunciated. This parameter is only visible if the configuration indicates that the compressor is equipped
with a variable speed motor and a separate motor speed input. The value is measured in rpm.

Instruction Manual | GEA Omni™
Control panel

Control

Compressor Control Parameters

GEA Refrigeration North America, Inc. | E_806550_2 | Generated 12.01.2016

119

«
...
117
118
119
120
121
...
»

Summary of Contents for Omni















































































































































































































































Reviews:

No comments

Related manuals for Omni

Brand: Warner Electric Pages: 3

Brand: iCeeO2 Pages: 7

Brand: SABAF Pages: 6

Brand: Accel Pages: 8

Brand: C3 Custom Coolers Pages: 16

Brand: Uclear Pages: 40

Brand: M-Audio Pages: 26

Brand: M Climate Pages: 12

Brand: U-Prox Pages: 3

Micro850 series

Brand: Allen-Bradley Pages: 24

Brand: HEROSE Pages: 92

Brand: L&L Pages: 16

8745 MFC Ethernet

Brand: Burkert Pages: 70

Brand: Tempco Pages: 12

Brand: zeeltronic Pages: 13

Brand: QD Dynamics Pages: 64

SatService sat-nms VLC

Brand: Calian Pages: 40

Brand: Nibe Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands