manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 98 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 98

6 - 18

     Reference and Specification

K0260 Issue No. 8

[View Manifold]

¤

This facility is the same as view manifold (above) but within the PIN protected area.

[Valve Calibration]

¤

The system operates the apply and release valves, measures performance, calculates 
and stores the characteristics of each valve. This takes approximately 20 minutes to 
complete.

Note:

To complete this set-up requires additional equipment and should only be carried out at 
approved equipment service centres.

[Work Valves]

¤

Should a valve be replaced and, before valve calibration, the new valve requires 
exercising to bed into the valve seat. The recommended time for this function is 8 hours. 
Selecting this function operates each apply and release valves every second until Cancel 
Test is selected.

[Cancel Test]

¤

This stops the work valves function.

[Calibrate Sensors]

¤

The calibration function requires the calibration switch on the front panel to be enabled. 
This procedure must be carried out by a qualified calibration technician, the details of 
calibration are contained in the Druck Calibration Manual for the ADTS 505.

[Auto Leak]

•

The ADTS 505 protects the aircraft system against leaks in the aircraft system.

 

The system 

protection operates:

¤

Automatically regains control if the leak rate is greater than the parameter rate (RtPt, 
ROC) during leak testing.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments