manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 44 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 44

3 - 16

Operation

K0260 Issue No. 8

3.7.1 Testing the Aircraft Static System

CAUTIONS:
1

O

BSERVE

 

ALL

 

SAFETY

 

PRECAUTIONS

 

DETAILED

 

IN

 

THE

 A

IRCRAFT

 M

AINTENANCE

 M

ANUAL

.

2

W

HEN

 

USING

 P

S

 (

STATIC

 

ONLY

), 

MAKE

 

SURE

 

THAT

 

THE

 

DIFFERENTIAL

 

PRESSURE

 (Q

C

) 

STAYS

 

WITHIN

 

THE

 

LIMITS

 

OF

 

THE

 ASI.

1.

Remove the static blanking cap and switch ON.

2.

Connect the ADTS 505 to the Aircraft Static System. 

Note:

If the static system under test contains an ASI, applying static (vacuum) to this instrument 
generates a Q

C

 differential pressure.

3.

Press 

ALT/Ps

 and make sure the display shows ALT Leak Measure. 

Note:

To monitor the rate of change press 

ROC/RATE Ps

 after pressing 

ALT/Ps

. The control rate of 

change for altitude can be changed within the selected limits.  

4.

If necessary, select [Units] in the Main Menu, press F1 [ft, kts, ft/min]. Press 

CLEAR/QUIT

 to go back 

to the Main Menu.

5.

If necessary change the limits in the Main Menu, press F6 [More], F1 [Limits]. After setting the limits, 
press repeatedly 

CLEAR/QUIT

 to go back to the Main Menu.

6.

Press 

LEAK MEASURE/CONTROL

 to select control mode and, using the numeric keys, set the control 

aim. Press 

ENTER

, the altitude changes to the control aim the rate of change slows as it gets near 

the control aim and does not "overshoot" the aim value. 

7.

Enter another aim or use the nudge facility to change the aim value. At the end of testing, press 

GROUND

 to return to atmospheric pressure.

8.

On completion of testing, select 

GROUND

 and wait for the `Safe at Ground' message to be displayed, 

see 3.7.8., refit the static blanking cap.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments