manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 40 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 40

3 - 12

Operation

K0260 Issue No. 8

Press 

LEAK MEASURE/CONTROL

 to select Control mode.

Using the set-up menu, choose the limits set for the aircraft or UUT, see 3.5.6.

Press 

CLEAR/QUIT

 repeatedly until the display shows control mode.

Set 

ROC/RtPs

 to 5000ft/min, enter an altitude aim of 1000 ft and an airspeed of 200 knots.

Wait until the system achieves the aim values and press 

LEAK MEASURE/CONTROL

 to 

change to Leak Measure mode.

Leak Measurement

Note:

Compressing a gas generates heat. Gas heated or cooled in an enclosed volume causes a 
pressure change. It is important, especially for leak testing, to allow enough time for the heated 
gas to cool and the pressure to stabilize.

In Leak Measure mode, select from the main menu [Rate Timer], and enter a wait time in minutes 
and seconds F3 - [Set Wait] 00m.30Secs. Enter a leak measure time in minutes and seconds F4 - 
[Set Time] 00m.30Secs. If necessary, press F5 to save these times for future use. 

Select [Start Timer] F1, as the rate timer starts, the display shows the count down (in seconds) of 
the wait time and then the count down of the timing. The status message at the bottom of the 
screen changes in this order LEAK MODE: WAIT: TIMING: RATES AVAILABLE: Wait until rate timer 
has completed, the rate parameters on the display changes from "Leak Measure" to "Timed Leak 
Measure" and shows the results in units/min.

•

Check ROC is less than ±25 ft/min and Rt CAS is less than ±0.25 kt/min.

•

Press CLEAR/QUIT to return to the main menu.

•

Press 

LEAK MEASURE/CONTROL

 to return to Control mode.

•

Press 

GROUND

, to go to atmospheric pressure.

•

Wait until the display shows safe at ground (atmospheric pressure).

After a successful leak test, the ADTS 505 is now ready to be connected to an aircraft system or 
unit under test.

After an unsuccessful, first-time leak test, leave the system to achieve thermal stability for a further 
five minutes, press 

CLEAR/QUIT

 and repeat the leak test. If the leak test is now successful, the 

ADTS 505 is now ready to be connected to an aircraft system or unit under test.

After another unsuccessful leak test, disconnect both hoses, check the condition of the o-rings on 
the Ps and Pt connectors as detailed in the maintenance section and firmly replace the blanking 
caps. Press 

CLEAR/QUIT

 and repeat the leak test procedure. 

After a successful leak test without hoses connected, replace or repair the faulty hose(s) and test 
again. If the ADTS 505 fails the leak test without hoses connected, switch off and return the unit 
to the repair depot.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments