manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 95 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 95

Druck ADTS 505 User Manual

         6 -  15

K0260 Issue No. 8

6

[Alt. Corr.]

Altitude Correction (Figures 6-2 and 6-3)

•

This function allows the altitude correction value to be changed. The display shows the 
altitude correction value in the lower part of the display screen.

•

The altitude correction facility corrects for the pressure difference when the ADTS 505 and 
the aircraft system or UUT are at different heights.

•

Enter the height difference between the aircraft system or UUT and the ADTS 505 reference 
level. If the ADTS 505 front panel is vertical, use a reference level of the mid point on the front 
panel. If the ADTS 505 front panel is horizontal, then use the reference level of the top of the 
case. If the aircraft system or UUT is below the ADTS 505, enter the value as a negative 
number.

•

The units of altitude correction are the current aeronautical units.         

F

IGURE

 6-2 A

LTITUDE

 

CORRECTION

 

ON

-

AIRCRAFT

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments