manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 37 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 37

Druck ADTS 505 User Manual

3 - 9

K0260 Issue No. 8

3

Go to GROUND

  

When the system is in control mode press:

 

     

Note:

 Go to ground does not operate in measure mode.

The ALT Aim value immediately changes to the current 
ground pressure (local airfield altitude) and the system 
safely controls to the GROUND value stored from 
power-up. The CAS Aim value immediately changes to 
zero and the system safely controls to zero:

The altitude and airspeed decreases at the rate set in 
ROC and RtCAS.
When the altitude and airspeed are at ground and zero 
the display changes to:

 
At ground and zero the display shows safe at ground for 5 
seconds then the ADTS 505 system closes the output valves 
to isolate the aircraft system and goes into a system datum 
check routine (includes operation of the pump and control 
valves) go to 3.7.8 for more details. 

After completion of the system datum check routine the 
display shows safe at ground and the message "Press Clear/
Quit to continue".
It is now safe to continue testing or to switch off and 
disconnect the aircraft system.

When familiar with these procedures go to 3.5.4 to leak test 
the ADTS 505.

ALT

Ps

SPEED

Qc

MACH

Pt

ROC

RATE Ps

GROUND

RATE

7

F6

F5

F4

F3

F2

F1

4

1

_

000

8

5

2

0

9

6

3

.

CLEAR

QUIT

ABORT

DELETE

ENTER

LEAK

MEASURE
CONTROL

HELP

SETUP

SAFE

AT

GROUND

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments