manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 61 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 61

Druck ADTS 505 User Manual

       4 -  5

K0260 Issue No. 8

4

Fuse Replacement (Fig 4-1)

Replace the fuse when detailed in Section 5, Testing and Fault Finding:

•

Set  the  power  switch  to  OFF.

Note: 

The power switch is not a power isolator as defined by EN61010.

•

Isolate the power supply to the instrument by disconnecting the power supply 
connector (1).

•

Unscrew and remove the fuse cap (2) and fuse cartridge (3) from the front panel and 
replace the fuse cartridge (3).

Note: 

Fit the correct type of fuse detailed in Section 2, Installation and on the front panel.

•

Refit the fuse cap (2) and fuse cartridge (3) to the front panel.

•

Reconnect power supply connector (1).

• 

Switch on the power supply. The instrument should now be operational.

•

If a fuse blows immediately on switch-on, contact the manufacturer or Service Agent.

F

IGURE

 4-1 F

USE

 R

EPLACEMENT

1

2

3

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments