manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 76 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 76

5 - 14

    Testing and Fault Finding

K0260 Issue No. 8

5.6

Fault Finding
System Messages

In the event of a malfunction, the built-in, self-test and diagnostic system displays a message 
and a code. The message heading 

Error

 indicates a fault or condition that interrupts normal 

operation. The following tables list the error messages with the probable cause and action to 
be taken.

If the display shows a message not listed in the tables the unit must be switched off. If the 
display shows the same non-operational message after switching on, the unit should be 
returned to the repair depot. 

 

T

ABLE

 5-3 E

RROR

 M

ESSAGES

Note:

 In No. 56, this safety feature opens the zero valve. If this happens constantly, check for leaks.

No.

Message

Probable Cause

Action

7

Autoleak recovery 
activated

Excessive leak rate detected in Ps/Qc 
pressures

Check hoses and aircraft systems for 
leaks

31

Test set must be at ground Invalid user request

Select Go to Ground first

32

Pressure leak in Ps. 

Leaking Ps channel pressure control 
valve.

Return unit to repair depot.

33

Pressure leak in Pt. 

Leaking Pt channel pressure control 
valve.

Return unit to repair depot.

36

Ps Aim Overshoot.

Connected system leak rate 
changing.

Check hoses and aircraft systems for 
leaks.

37

"Ps aim value 
unobtainable".

Leak rate on Ps too high to control.

Check port caps, hoses and 
connectors for leaks.

40

Pt Aim Overshoot.

Connected system leak rate 
changing.

Check hoses and aircraft systems for 
leaks.

41

"Pt aim value 
unobtainable".

Leak rate on Pt too high to control.

Check port caps, hoses and 
connectors for leaks.

4

Vacuum leak in Ps. 

Leaking Ps channel vacuum control 
valve.

Return unit to repair depot.

4

Vacuum leak in Pt. 

Leaking Pt channel vacuum control 
valve.

Return unit to repair depot.

4

Ps pressure control valve 
cannot be calibrated.

Valve fault.

Return unit to repair depot.

56

Stabilising Qc to Zero.

Possible negative airspeed detected, 
possible sudden leak. 

System zero valve opened to stop 
negative airspeed condition. 

57

Current Pressure Limits 
Exceeded.

Limits for Ps or Qc exceeded.

Make sure pressures are within limits, 
check leak rates.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments