manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 11 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 11

ix

K0260 Issue No. 8

Glossary

Terminology

The terminology used in this manual is specific and individual interpretation must not be 
introduced.  The terms are defined as follows:

Adjust

To bring to a more satisfactory state; to manipulate controls, levers, linkages, etc. to return equipment 
from an out-of-tolerance condition to an in-tolerance condition.

Align

To bring into line; to line up; to bring into precise adjustment, correct relative position or coincidence.

Assemble:To fit and secure together the several parts of; to make or form by combining parts.

Calibrate: To determine accuracy, deviation or variation by special measurement or by comparison with a 

standard.

Check:

Make a comparison of a measure of time, pressure, temperature, resistance, dimension or other 
quality with a known figure for that measurement.

Disconnect:To detach the connection between; to separate keyed or matched equipment parts.

Dismantle:To take apart to the level of the next smaller unit or down to all removable parts.

Examine: To perform a critical visual observation or check for specific conditions; to test the condition of.

Fit:

Correctly attach one item to another.

Inspect: Review the work carried out by Specialists to ensure it has been performed satisfactorily.

Install:

To perform operations necessary to properly fit an equipment unit into the next larger assembly or 
system.

Maintain: To hold or keep in any particular state or condition especially in a state of efficiency or validity.

Operate: Make sure that an item or system functions correctly as far as possible without the use of test 

equipment or reference to measurement.

Readjust: To adjust again; to move back to a specified condition; to bring back to an in-tolerance condition.

Reconnect:To rejoin or refasten that which has been separated.

Refit:

Fit an item which has previously been removed.

Glossary

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments