manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 67 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 67

Druck ADTS 505 User Manual

       5 -  5

K0260 Issue No. 8

5

T

ABLE

 5-1 F

AULT

 F

INDING

      

Fault

Symptom

Probable cause

Action

F1

Power supply indicator 
does not light.

Faulty power supply outlet. 
Unserviceable power supply front
panel fuse.
Faulty power supply cable.

Internal power supply fault.

Check power supply.
Check/replace fuse.
Check/replace fuse.
Replace cable and re-test.

Record fault and return ADTS 505 
to depot for repair.

F2

Power supply indicator 
lights, no display.

Internal fault.

Record fault and return ADTS 505 
to depot for repair.

F3

No self-test message.

Internal fault.

Record fault and return ADTS 505
to depot for repair.

F4

Display shows error 
message.

Error detected.

Refer to fault finding tables.

F5

Display does not show 
Leak Measure mode.

If display stops at Thermal Test.

System component fault.

Allow ADTS 505 to reach ambient
temperature.
Record fault and return ADTS 505
to depot for repair.

F6

Fails SST.

Internal leak.

Internal fault.

Refer to further testing 5.5.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments