manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 39 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 39

Druck ADTS 505 User Manual

3 - 11

K0260 Issue No. 8

3

3.5.3 Control or Measure Parameter

To change the displayed Measure parameters:
Press 

SETUP

 [Displays], [Single, Dual, Quad], press 

CLEAR/QUIT

 repeatedly until the display goes 

to Leak Measure Mode.

Measure parameters:

Press the parameter key
e.g., press 

SPEED/Qc

 to display airspeed.

To change the displayed rate parameter:

Press the associated parameter key followed by the rate key.
e.g., display airspeed rate, press 

SPEED/Qc

 then 

RATE

.

ROC/RATE Ps

 may be directly pressed without first pressing 

ALT/Ps

.

In Leak Measure mode, pressing the parameter and rate keys changes the order that the display 
shows the parameters.

Control Aim

A new control aim can be entered using the numeric keys. Each digit is displayed as it is pressed. 
The existing aim is replaced when the first digit of the new aim is pressed. If an error is made during 
the entry of data, press 

CLEAR/QUIT

 to restore the original aim.

Press 

ENTER

 to action the new aim.

Note 1:

The 

-/000

 key can be used as a quick way of entering thousands. If this key is pressed first (i.e. 

before a number is entered) the value becomes negative, press again the value becomes positive. 

Note 2:

The ADTS 505 must be in control mode to enter a new aim (current aim displayed). If the aim 

field shows "Leak Measure" press 

LEAK MEASURE/CONTROL

 to enter control mode.

3.5.4 Leak Testing the ADTS 505

It is important to check that the ADTS 505 and the connecting hoses do not leak. Before use, a leak 
check should be carried out as follows:

Connect the Pitot and static hoses (to front panel of ADTS 505). Temporarily seal the free ends of 
the hoses. 

Set the display to quad, see 3.4.1. Set the units to feet and knots, see 3.5.5.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments