manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 47 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 47

Druck ADTS 505 User Manual

3 - 19

K0260 Issue No. 8

3

3.7.4 Mach Test and Constant Mach
Example

To go to 0.45 Mach, proceed as follows: 

•

Press 

LEAK MEASURE/CONTROL

 to enter Control Mode.

•

Press 

SPEED/Qc

 then 

RATE

 to display rate of change of airspeed. 

•

The preset rate of speed is 300 kts/min.

•

Press 

MACH/Pt

.

•

Enter an aim of 0.45. 

•

Wait for the Mach aim to be achieved.

•

The system keeps the Mach aim constant by controlling/changing Pt (pitot) leaving Ps 
(static) at a constant value.

On completion of testing, select 

GROUND

 and wait for the `Safe at Ground' message to be displayed, 

see 3.7.8., refit the pitot and static blanking caps.

Notes

1

If the altitude Ps (static) changes, the system automatically adjusts Pt (pitot) to keep the Mach 
value constant.

2

Use the nudge facility for small changes to the Mach aim value.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments