manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 82 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 82

6 - 2

     Reference and Specification

K0260 Issue No. 8

ALT Ps

•

In aeronautical units (ft or m), this key selects an altitude display.

•

In pressure units (mbar, inHg etc.), this key selects a static pressure (Ps) display.

•

Select [Units], from the main menu, to change the display units.

•

Before entering a new altitude or Ps aim, set the rate of change using the 

ROC/RATEPs

 key.

•

When in Control Mode (Aim display), enter a new altitude or Ps aim using the numeric keys. 
Use 

LEAK MEASURE/CONTROL

 to change between Control and Leak Measure mode.

SPEED Qc

•

In aeronautical units (kts, km/h), this key selects an airspeed (CAS) display. In pressure units 
(mbar, inHg etc.), this key selects dynamic pressure and the display shows (Qc).

Note:

For testing purposes, Calibrated Airspeed (CAS) equates to Indicated Airspeed (IAS).

•

If the altitude aim is changed, after the entry of CAS, the Mach aim value changes while the 
CAS value remains unchanged.

•

If the altitude aim is changed, after the entry of Mach, the CAS aim value changes while the 
Mach value remains unchanged.

•

If the Ps aim is changed, after the entry of Qc, then the Pt aim value changes while the Qc 
remains unchanged.

•

If the Ps aim is changed, after the entry of Pt, then the Qc aim value changes while the Pt 
remains unchanged.

•

Select [Units], from the main menu, to change the display units.

•

The rate of change is fixed at 300 kts/min or equivalent.

•

When in Control Mode (AIM display), a new CAS or Qc can be entered using the numeric keys. 
Use 

LEAK MEASURE/CONTROL

 to change between Control and Leak Measure mode.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments