manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 74 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 74

5 - 12

    Testing and Fault Finding

K0260 Issue No. 8

Vacuum leak check

This procedure verifies that the unit is leak tight under vacuum conditions.

(1)

Press 

LEAK MEASURE/CONTROL

 to enter control mode.

(2)

Enter an ALT/Ps Aim of 100 mbar.

(3)

Enter a Speed/Qc Aim of 0 mbar. 

(4)

Wait the required time for temperature stabilization e.g., one minute. Press 

LEAK 

MEASURE/CONTROL

 return to Leak Measure mode.

(5)

Select [Rate Timer] and select [Set Wait 05:00], [Set Time 01:00] and then select [Start 
Timing]. 

(6)

At the end of the timing period, press 

ROC/RtPs

 to display the measured rate of change 

of ALT/Ps. 

(7)

Check that the Ps, Qc and Pt rates are less than or equal to ±0.5 mbar/min. If the leak 
rate is not achieved, allow further thermal stabilization time and re-test by selecting 
[Rate Timer] and select [Set Wait 05:00], [Set Time 01:00].

(8)

Press 

CLEAR/QUIT

 to exit rate timer display.

Range check

Control the Ps and Qc pressures to the normal limits of operation and make sure that these 
are achieved. Use minimum Ps and zero Qc and then maximum Ps and maximum Qc.

Note:

Do not exceed the maximum Pt as shown on the front panel of the unit. Use 
maximum available rates of change to minimise test times.

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments