manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 41 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 41

Druck ADTS 505 User Manual

3 - 13

K0260 Issue No. 8

3

3.5.5 Changing the Units of Measurement   

The units of measurement can be changed 
to units of pressure measurement or 
aeronautical units.

To change the units:

•

Select, from the main menu, [Units].

•

Select from the Units Menu:

•

Select [Save Settings] to store as the 
units used at the next power up.

•

Press 

CLEAR/QUIT

 to return to the 

main pressure display.

•

In set-up, more units of pressure 
measurement can be selected for 
each parameter.

3.5.6 Setting Limits

All data entered is checked against minimum and maximum values set for the particular limit set 
in use. If these limits are exceeded, the display shows a warning message "Changed aim to current 
limit". Press 

CLEAR/QUIT

 the system automatically modifies the aim values so that the limits are 

not exceeded. All limits of associated parameters are checked, if these limits are exceeded the 
display shows the warning message and the parameter modified. Similarly, if an ARINC 565 limit 
is exceeded when entering a value and, ARINC limits are enabled, the display shows a warning 
message. Refer to Section 6 for details of the factory-defined operating envelope ARINC565.

In the SETUP function, previously stored sets of limits can be selected for use. Each set of limits is 
stored under name or number up to a maximum of 10 characters. To enable other sets of limits 
or enter additional sets of limits requires the supervisor PIN.

F1

F2

F3

F4

F5

F6

F2

Units

Main Menu

ft kts
ft/min

m km/h
m/min

mbar
mbar/min
Save
Settings

Units

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments