GE Druck ADTS 505 User Manual Download Page 77

Page: 77 / 124

Druck ADTS 505 User Manual

5 - 15

K0260 Issue No. 8

ABLE

5-3 E

RROR

ESSAGES

(

CONTINUED

)

No.

Message

Probable Cause

Action

219

Abort sequence started by user

Abort key pressed on
hand terminal

Wait until system completes abort
sequence

220

"Cannot Modify Altitude
Correction in Pressure Units"

Altitude Correction

Change units in setup to aero units

221

"Changed Aim to ARINC Limit"

Value out of ARINC limit
range

Re-enter value within allowed range

222

Calibration data failed

Incorrect pressure
value entered during
calibration

Check and enter correct pressure
value for reference pressure point

223

"Cannot enter EPR in Aero Units"

EPR selected with aero
units displayed

Change units in setup to pressure
units then select EPR

227

"Changed Aim to Current Limit"

Value out of limit range Re-enter value within allowed range

228

"Limit Overlap"

Value conflicts with
limit ranges

Re-enter value within allowed range

229

"Limit Saved"

Value out of acceptable
range

Re-enter value within allowed range

241

"Ground Request in Leak Mode"

System must be in
control mode

Select control mode

243

"LDK has an invalid EEPROM
archive"

Invalid/corrupted data
- recovery in progress Check custom limit sets not lost

245

"Controller has an invalid EEPROM
archive"

Invalid/corrupted data
- recovery in progress Check/correct calibration

247

"Handset has an invalid EEPROM
archive"

Invalid/corrupted data
- recovery in progress

250

"Vacuum pump processor has
failed"

Internal fault

Return unit to repair depot

251

"Vacuum pump lead is
disconnected"

Return unit to repair depot

252

"Vacuum pump transistor is faulty
or drive inhibited"

Internal fault

Return unit to repair depot

Summary of Contents for Druck ADTS 505





























































































































Search results

Summary of Contents for Druck ADTS 505

Reviews:

GE Druck ADTS 505, User Manual, Page: 77 / 124

Search results

Summary of Contents for Druck ADTS 505

Reviews: