GE Druck ADTS 505 User Manual Download Page 113

Page: 113 / 124

Druck ADTS 505 User Manual

6 - 33

K0260 Issue No. 8

Example Test Table

Note:

The pressure and aero units shown have been validated for these procedures. Using any

other units in an up-loaded file may not be accepted by the advanced hand terminal.

Test Identifier

Begin Test Table

Parameter Label

Prompt Message

REF (a)

REF (b)

Test Identifier

Begin Test Table

Parameter Label

Prompt Message

Case Leak Test

Max. Allowed Leak Rate

+/- 100 feet/min

End of Test

When stable> Leak Measure>

Go to ground

Ps1 Aim

Ps1 Rate

Ps2 Aim

Ps2 Rate

Pt Aim

Pt Rate

<AIM UNIT> <AIM UNIT>

<AIM UNIT> <RATE UNIT> <

UNIT>

RATE

UNIT>

RATE

<Ps1

Rate (a)

<Ps1

(b)

Rate

<Ps1

(c)

Rate

<Ps1

(d)

Rate

<Ps1

(e)

Rate

<Ps2

(a)

Rate

<Ps2

(b)

Rate

<Ps2

(c)

Rate

<Ps2

(d)

Rate

<Ps2

(e)

Rate

<Pt

(a)>

Rate

<Pt

(b)>

Rate

<Pt

(c)>

Rate

<Pt

(d)>

Rate

<Pt

(e)>

Rate

Ps1 Aim

Ps1 Rate

Ps2 Aim

Ps2 Rate

Pt Aim

Pt Rate

feet

knots

feet/min

knots/min

18000

6000

300

6000

300

Pressure Units

(for Ps, Pt, Qc)

Assumed Rates

for Pressure Units

mbar

mbar/min

inHg

inHg/min

psi/min

psi

mmHg

mmHg/min

inH2O4C

inH2O20C

InH2O60F

kPa

hPa

inH2O4C/min

inH2O20C/min

inH2O60F/min

kPa/min

hPa/min

Aero Units
(for Altitude and Speed)

Matching Rate
of Aero Units

feet

feet/min

For Altitude:

m/min

For Speed:

knots

knots/min

kph

kph/min

mph

mph/min

Mach

knots/min

Aero Units

for Altitude

Matching Speed

Units

feet

knots

feet

mph

kph

Any of the above

Mach

Summary of Contents for Druck ADTS 505





























































































































Search results

Summary of Contents for Druck ADTS 505

Reviews:

GE Druck ADTS 505, User Manual, Page: 113 / 124

Search results

Summary of Contents for Druck ADTS 505

Reviews: