manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 52 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 52

3 - 24

Operation

K0260 Issue No. 8

3.8

Manual Venting of the Aircraft Pitot and Static Systems

This procedure should be carried out when the power supply has failed and the ADTS 505 has 
failed-safe with pressures remaining in the aircraft system. The aircraft system pressures must be 
slowly changed to atmospheric pressure in the following way:

CAUTION:

1

T

HE

 

AIRCRAFT

 

INSTRUMENTS

 

MUST

 

BE

 

MONITORED

 

THROUGHOUT

 

MANUAL

 

VENTING

. D

O

 

NOT

 

EXCEED

 

THE

 

MAXIMUM

 

RATES

 

OF

 

CHANGE

 

OF

 

PRESSURES

 

FOR

 

THE

 

INSTRUMENTS

 

IN

 

THE

 

AIRCRAFT

 

SYSTEM

. R

EFER

 

TO

 

THE

 A

IRCRAFT

 M

AINTENANCE

 M

ANUAL

.

2

F

OLLOW

 

THIS

 

PROCEDURE

; 

DO

 

NOT

 

PRODUCE

 

A

 

NEGATIVE

 

AIRSPEED

 

THIS

 

WILL

 

DAMAGE

 

AIRCRAFT

 

INSTRUMENTS

. 

i.

Using a screwdriver, carefully open the Qc manual vent and allow the pressure in the pitot 
(Pt) and static (Ps) systems to equalise (shown on the aircraft ASI). Fully open the Qc valve.

ii.

Using a screwdriver, carefully open the Ps manual vent do not exceed a rate of 3000 ft/min.

iii.

When the indicated pressures, shown on the aircraft instruments, reaches atmospheric 
pressure close both vents.

3.9

ADTS 505 Options

Hand Terminal Option A

The hand terminal provides the same selections and displays as the front panel display. When 
connected the system auto-detects the hand terminal and disables the front panel key-pad.

 

The front panel display shows "Remote Hand Terminal Operating" (message/monitor) or the current 
values and modes of the hand terminal (monitor). The display menu in set-up provides the selection 
between message and monitor.

Advanced Hand Terminal Option B

CAUTION:

O

NLY

 

USE

 

THIS

 

ADVANCED

 

HAND

 

TERMINAL

 

WITH

 ADTS 505 

UNITS

 

AT

 

MODIFICATION

 

STATE

 3, 

DAMAGE

 

WILL

 

OCCUR

 

TO

 ADTS 505 

UNITS

 

AT

 

EARLIER

 

MODIFICATION

 

STATES

.

•

During the early power-up, self-test period, the instrument display screen shows:

 

”Software Version 1.07+”

This text is located just above the last calibration date entry. 

The advanced hand terminal provides a Windows®-based, touch-sensitive colour screen to up-
load and down-load user-defined test programs. When connected, the system auto-detects the 
advanced hand terminal and disables the front panel key-pad. The front panel display shows 
"Remote Hand Terminal Operating" (message/monitor) or the current values and modes of the 
advanced hand terminal (monitor). At power-up, the display shows the main operation menu with 
selections for system set-up, test sequence files and manual control. See 6.4 for the details and 
procedures for the advanced hand terminal.

If the ADTS 505 unit is not at the correct modification state, contact the local GE Sensing sales team 
to arrange for a free upgrade of your unit.

www.ge-mcs.com

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments