manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 51 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 51

Druck ADTS 505 User Manual

3 - 23

K0260 Issue No. 8

3

3.7.8 Go To Ground

On completion of testing and, before disconnecting from the aircraft system or UUT, the pressures 
in the system must be taken to the local atmospheric pressure (ground) with zero airspeed.

•

If the display shows "Leak Measure", press 

LEAK MEASURE/CONTROL

.

•

Press 

GROUND

, (go to ground).

•

The pressure in the system changes towards ground. The ground pressure replaces the 
static or altitude aim value; zero replaces the airspeed aim.

Note:

If required, new rates of change can be entered while going to ground.

•

Wait for the display to show zero airspeed and atmospheric pressure. 

•

The display changes to "safe at ground" for 5 seconds then to "aircraft safe at ground" 
with the message "confirming system settings .....".

Note:

During this operation:

keep the power supply connected and switched on. 

the system disables the key-pad.

it is safe to disconnect the pipes from the aircraft system or UUT.

•

After completing this operation the display changes back to "safe at ground" with the 
message "Press Clear/Quit to continue".

 

•

It is now safe to continue testing or to switch off and disconnect the aircraft system or 
UUT.

Note:

If the ADTS 505 stays in the "safe at ground" for 30 minutes the  
"confirming system settings ....." operation will be repeated. The 
operation automatically re-checks the ADTS controller settings, 
the pumps start and the display shows:     

No pressure is applied to the output ports during this operation.

Shut-down

•

When the airspeed is zero and the Ps channel pressure is close to ground, the 
atmospheric pressure is re-measured to update the recorded ground pressure (QFE). 

•

Press 

QUIT/CLEAR

 to continue with normal operation; the ground and zero valves 

automatically close.

ALT

Ps

SPEED

Qc

MACH

Pt

ROC

RATE Ps

GROUND

RATE

7

F6

F5

F4

F3

F2

F1

4

1

_

000

8

5

2

0

9

6

3

.

CLEAR

QUIT

ABORT

DELETE

ENTER

LEAK

MEASURE
CONTROL

HELP

SETUP

AIRCRAFT

SAFE AT

GROUND

confirming system settings 1 of 4....

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments