manualshive.com logo in svg

GE Druck ADTS 505, User Manual, Page: 90 / 124

Share
Download
GE Druck ADTS 505 User Manual Download Page 90

6 - 10

     Reference and Specification

K0260 Issue No. 8

[EPR]

•

Engine Pressure Ratio only operates in units of pressure measurement (mbar, inHg etc.) with 
a set of pre-defined limits, see section 1. The ADTS 505 can be used to check EPR sensors, 
indicators and EPR data for engine control systems.

Note:

Altitude correction applies to EPR values, make sure this correction does not adversely 
affect accuracy. The difference in height between the ADTS 505 and the EPR sensor may 
be different to the altitude correction previously set for the aircraft instruments.

•

For EPR testing, use Ps as INLET pressure and EPR to set the ratio of OUTLET pressure (Pt) to 
INLET pressure (Ps).

•

Before entering a new EPR aim, the rate of change should be set by selecting [EPR Rate] on 
the Main Menu.

•

When in Control Mode (AIM display), a new EPR aim can be entered using the numeric keys. 
Use 

LEAK MEASURE/CONTROL

 to change between Control and Leak Measure mode.

Rate EPR

•

When in Control Mode (AIM display), the rate of pressure change can be set using the 
numeric keys. Use 

LEAK MEASURE/CONTROL

 to change between Control and Leak Measure 

mode.

[Hold]

•

Selecting [HOLD] causes a changing pressure to instantaneously hold. Selecting [HOLD] 
again releases the pressure to continue to the aim value. The [HOLD] facility applies to both 
channels simultaneously.

•

[HOLD] automatically releases when 

LEAK MEASURE/CONTROL

 is pressed entering Measure 

Mode.

[Nudge]

•

Changes the current aim value [  or  ] by a set increment value (2 ft, 0.2 kts, Mach 0.02).

•

This facility can be used to align a pointer of an instrument to a precise indicated value and 
compare this indicated value with the measured value.

•

This facility may be used for pressure switch testing as follows:

¤

Aim for a pressure just below the expected operating point.

¤

When the pressure is achieved, repeatedly press   until the switch operates.

¤

Record the pressure reading shown on the display.

•

Repeat this procedure using the   until the switch returns to its original condition, refer to 
section 3 for an example. 

Summary of Contents for Druck ADTS 505





























































































































Reviews:

No comments