Chapter 12 Description of Parameter Settings
MS300
(High Speed Model)
12-09-10
Content
Register
Function
2210H
The status of digital input (ON / OFF), refer to Pr. 02-12
(as Pr. 00-04 NOTE 3)
2211H
The status of digital output (ON / OFF), refer to Pr. 02-18
(as Pr. 00-04 NOTE 4)
2212H The multi-step speed that is executing (S)
2213H
The corresponding CPU pin status of digital input (d.)
(as Pr. 00-04 NOTE 3)
2214H
The corresponding CPU pin status of digital output (O.)
(as Pr. 00-04 NOTE 4)
2215H
Number of actual motor revolution (PG1 of PG card) (P.) it will
start from 9 when the actual operation direction is changed or
keypad display at stop is 0. Max. is 65535
2216H Pulse input frequency (PG2 of PG card) (XXX.XX Hz)
2217H
Pulse input position (PG card PG2), maximum setting is
65535.
2218H Position command tracing error
2219H Display times of counter overload (XXX.XX %)
221AH GFF (XXX.XX %)
221BH DC-BUS voltage ripples (XXX.X V)
221CH PLC register D1043 data (C)
221DH Pole of Permanent Magnet Motor
221EH User page displays the value in physical measure
221FH Output Value of Pr. 00-05 (XXX.XX Hz)
2220H
Number of motor turns when drive operates (keeping when
drive stops, and reset to zero when operation)
2221H
Operation position of motor (keeping when drive stops, and
reset to zero when operation)
2222H Fan speed of the drive (XXX %)
2223H Control mode of the drive 0: speed mode 1: torque mode
2224H Carrier frequency of the drive (XX KHZ)
2225H
Reserved
2226H
Drive status
bit 1~0 00b: No direction
01b: Forward
10b: Reverse
bit 3~2 01b: Driver ready
10b: Error
bit 4 0b: Motor drive did not output
1b: Motor drive did output
bit 5 0b: No alarm
1b: Have Alarm
2227H
Drive’s estimated output torque (positive or negative direction)
(XXXX Nt-m)
2228H Torque command (XXX.X %)
2229H KWH display (XXXX.X)
222AH MI7pulse input in Low Word
222BH MI7 pulse input in High Word
222CH Motor actual position in Low Word
222DH Motor actual position in High Word
222EH PID reference (XXX.XX %)
222FH PID offset (XXX.XX %)
2230H PID output frequency (XXX.XX Hz)
2231H
Hardware
ID
2232H Display auxiliary frequency
2233H Display master frequency
2234H
Display frequency after addition and subtraction of auxiliary
and master frequency
Summary of Contents for VFD11AMS21AFSHA
