Daedong Kioti RX6020 Manual Download

Page: 218 / 262

rx6020 / rx6620 / rx7320 / rx7620

READJUsTMENT

(1) tie rod lock nut

(2) tie rod

1. loosen the lock nut and turn the

turnbuckle to adjust the rod length

until the proper toe-in measure-

ment is obtained.

2. check the toe-in value after the tie

rod is adjusted.

3. adjust it again if necessary.

M55O782A

check to ensure the radiator hoses

are free from damage and are tight-

ened properly every 200 hours or ev-

ery 6 months, whichever comes first.

1. if the hose clamps are loose or

water leaks from hose, tighten

clamps securely.

2. if the radiator hoses are swollen,

hardened, cracked, or otherwise

damaged, you must replace the

hoses. failure to do so could lead

to coolant loss and engine damage.

(1) clamp

(2) hose

CHECKINg RADIATOR HOSE AND CLAMP (Z)

PRECAUTION AT OvERHEATINg

take the following actions in the

event the coolant temperature reach-

es the boiling point, what is called

"over-heating".
1. stop the machine in a safe place

and keep the engine idling.

2. after 5 minutes of unloaded idling,

shut the engine down.

3. keep yourself away from the trac-

tor for another 10 minutes or until

steam has stopped blowing out of

the engine.

4. make sure that there is not danger

and repair the cause of the over-

heating according to the manual’s

instruction.

M55O783A

TF110(RX7320)ROPS합본-US,EU,AU-07.30 30

2016-05-10 오전 8:50:56

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands