Daedong Kioti RX6020 Manual Download Page 220

Page: 220 / 262

rx6020 / rx6620 / rx7320 / rx7620

(1) net

(2) condenser

(3) oil cooler

ClEANING AIR CONDITIONER

CONDENsER (AC)

1. pull the hood lever on the right

side forward to open the hood.

2. undo the wing bolt and pull the

grill to the right side to remove it.

remove the oil cooler as neces-

sary to clean the condenser.

Make sure to stop engine

when checking. If cooler fan is

blocked by dirt, clean with a soft

brush or cloth using water.

•

CAUTION

T11O719A

ADjUSTINg FRONT AxLE PIvOT

(AD)

(1) adjusting Bolt

(2) lock nut

T11O741A

if the front axle pivot pin adjustment

is not correct, front wheel vibration

can occur causing vibration in the

steering wheel

ADjUSTINg PROCEDURE

loosen the lock nut, tighten the ad-

justing screw all the way, and then

loosen the screw by 1/6 turn. re-

tighten the lock nut.

engine operation can be adversely

effected by this adjustment. there-

fore, contact your local

kIOTI

Dealer

for this service.

ADJUsTING ENGINE VAlVE

ClEARANCE (AE)

TF110(RX7320)ROPS합본-US,EU,AU-07.32 32

2016-05-10 오전 8:50:57

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 220 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: