Daedong Kioti RX6020 Manual Download Page 169

Page: 169 / 262

opERATIoN

CONNECTING AND DISCONNECTING IMPLEMENT

CONNECTION

1. make sure to stop the engine be-

fore connecting implements.

2. move the double acting valve le-

ver forward and backward for 4

to 5 times to release the pressure

in the hydraulic line of the tractor.

otherwise, it is hard to connect the

couplers, and hydraulic fluid can be

sprayed from the line and get in to

your eyes while connecting them.

3. Remove any foreign material

around the male and female cou-

plers. If foreign material enters the

hydraulic components, it can lead

to malfunction of the system.

4. open the dust-proof cover of the

female coupler of the tractor and

insert the male coupler of the im-

plement. A clicking sound is heard

when the couplers are engaged.

5. pull the hydraulic hose of the im-

plement to check that the couplers

are properly connected.

6. Start the engine and check the op-

erating status and leakage.

DISCONNECTION

1. make sure to stop the engine be-

fore disconnecting implements.

2. Release any residual pressure in

the hydraulic hoses of the imple-

ment and tractor by operating the

double acting valve lever 4 to 5

times.

3. Remove any foreign material

around the couplers.

4. lower the implement on the

ground or remove any external

load applied to the implement. dis-

connecting hoses while outer load

is applied to the implement is very

difficult and dangerous due to the

pressurized fluid in the hose.

5. Remove the male coupler by push-

ing the female coupler boss back-

ward.

6. Close the dust-proof cover of the

female coupler. Wrap the male

coupler of the implement with a

plastic bag to prevent contamina-

tion.

Never connect or disconnect

the implement hydraulic hose

while the pressure in it is not

released or the engine is run-

ning. It is hard to connect and

disconnect the hose and hy-

draulic fluid can be sprayed

from the hose, and get into

your eyes or skin.

Stop the engine and wear pro-

tective glasses and gloves be-

fore work.

•

WARNING

TF110(RX7320)ROPS합본-US,EU,AU-05.29 29

2016-06-07 오후 7:20:37

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 169 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: