Daedong Kioti RX6020 Manual Download Page 2

Page: 2 / 262

This manual was compiled in compliance with the ISO 3600, standards and the instructions contained here comply with

the requirements of the Machinery Directive 2010/52/EU in force in the European Community. For tractors sold or used

outside the European

Community,

local laws will prevail.

Main protections on the tractors discussed in this manual.

DeSCRIPTION

NON CANOPY

CANOPY

1. ROPS (protection against overturning)

Yes

2. FOPS (protection against objects falling from above)

Yes

3. OPS (protection against penetration of objects from sides)

protection against hazardous chemicals

(Category

Ⅰ)

(Category

Ⅰ)

ISO 3600 eU STANDARDS

TF110(RX7320)ROPS합본-US,EU,AU-00.2 2

2016-06-07 오후 6:55:20

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 2 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: