Daedong Kioti RX6020 Manual Download Page 39

Page: 39 / 262

safetY precautions

cautions for decal maintenance

safety decals are attached to the

tractor for safe operation. make sure

to follow the instruction on the decals

as well as the following instruction:



Keep the decals clean and in-

tact. if any decal is dirty, wash

it with soap and dry with a soft

cloth.



never use a solvent, such a

thinner or acetone, since it

can ruin the decals.



do not spray high-pressure

water directly onto the decal.

the decal may fall off the trac-

tor.

caution



if a decal is damaged or lost,

contact your local Kioti deal-

er immediately to install a new

decal.



make sure to attach the decal

in the correct position cleanly

without bubbles after cleaning

its mounting surface.



if a decal is attached to a com-

ponent to be replaced, replace

the decal as well.

imPortant

TF110(RX7320)ROPS합본-US,EU,AU-01.27 27

2016-06-07 오후 7:07:10

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 39 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: