Daedong Kioti RX6020 Manual Download Page 207

Page: 207 / 262

maintenance

ADjUSTINg BRAKE PEDAL (O)

(1) Brake pedal

(a) free play

M55O7B6A

adjust the brake pedal free play pe-

riodically. refer to the "maintenance

schedule chart" for checking interval.
the brake pedal can be adjusted as

follows:
1. release the parking brake and un

lock the pedal inter-lock.

2. slightly depress the pedals by

hand to measure the free play.

To avoid personal injury:



Stop the engine and chock the

wheels before checking brake

pedal.

3. when adjustments are needed,

loosen the locking nut and turn the

turn buckle until the rod length is

at the desired and acceptable limit.

4. re-tighten the lock nuts.
5. perform the same procedure for

the left brake pedal to make both

free play the same.

6. interlock the brake pedals after

checking or adjusting them.

CAUTION

Proper

brake

pedal

free travel

(A)

0.591 ~ 1.181 in.

(15 ~ 30 mm)

keep the free play in

the right and left brake

pedals equal.

(1) lock nut

(2) turn Buckle

M55O7e1A

TF110(RX7320)ROPS합본-US,EU,AU-07.19 19

2016-05-10 오전 8:50:49

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 207 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: