manualshive.com logo in svg

Daedong Kioti RX6020, Manual, Page: 222 / 262

Share
Download
Daedong Kioti RX6020 Manual Download Page 222

7

-

rx6020 / rx6620 / rx7320 / rx7620

REPLACINg  AIR FILTER (AI)

(1) Bolt 

  (2) filter

1. after  loosening  bolts  from  the  left 

and  right  side  of  the  cabin  roof  

then separate the filter. 

T11O742A

flUsh COOlING sysTEM AND ChANGING COOlANT (AJ) 

1. stop the engine and let it cool.
2. to drain coolant, remove the drain 

plug  from  the  radiator  and  turn 

the radiator cap to the 1

st

 notch to 

release  pressure  in  the  radiator. 

then, remove the cap completely.

3. after  all  coolant  is  drained,  close 

the drain cock.

4. fill  with  clean  water  and  anti-

freeze.

5. install the radiator cap securely.

(1) Drain cock

(1) reservoir tank

(a) full 

  (B) low

6. add  coolant  to  the  reservoir  tank 

to the "full" level.

7. start  and  operate  the  engine  for 

few minutes.

8. stop engine and let cool.
9. check  coolant  level  of  reservoir 

tank  and  radiator. add  coolant  if 

necessary.

Coolant capacity

 2.4 u.s. gal. (9.1 l)

T11O720AA

T11O704A

TF110(RX7320)ROPS합본-US,EU,AU-07.34   34

2016-05-10   오전 8:50:58

Summary of Contents for Kioti RX6020







































































































































































































































































Reviews:

No comments