Daedong Kioti RX6020 Manual Download

Page: 227 / 262

maintenance

REPLACINg FUSE (AN)

T11O744A

fuses protect the tractor electrical

system from potential damage.
a blown fuse indicates that there

is an overload or short somewhere

in the electrical system. if a fuse is

blown, find and remove the fault.

then replace it with a new fuse with

the same capacity.

(1) fuse Box

IGNITION

ALTERNATOR

15A

PBatt

ECU_RELAY

Spar

Spare

15A

Spare

15A

ECU_KEY_ON

Spare

T11O752A

Never use a fuse with the ca-

pacity higher than specified

on the fuse box cover.

If using a faulty fuse, steel

wire, or foil, the electrical de-

vice can be damaged or even

catch a fire.

•

WARNING

if the replaced fuse is blown, it is

probable that the wiring system

is faulty. in this case, contact

your local

kIOT

i Dealer.

if the fusible link, relay or other

electrical component is faulty,

contact your local

kIOT

i Dealer.

•

NOTE

TF110(RX7320)ROPS합본-US,EU,AU-07.39 39

2016-05-10 오전 8:51:00

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands

Daedong Kioti RX6020, Manual

Search results

Summary of Contents for Kioti RX6020

Reviews:

Related manuals for Kioti RX6020

Brands by name

Popular brands