Daedong Kioti RX6020 Manual Download Page 18

Page: 18 / 262

rX6020 / rX6620 / rX7320 / rX7620

3. do not operate your tractor in an

enclosed building without the prop-

er ventilation. Exhaust containing

carbon monoxide can cause seri

ous injury or death.

T66O110a

4. make sure that all pressure lines

are tight before starting the tractor.

5. the front hitch receiver can be

installed on front axle frame. Pull

only from the draw-bar and front

hitch receiver.

never hitch

anything to the aXle hous-

ing or any other Point

eXcePt indicated Points.

pulling from any other location

only increases the risk of serious

personal injury or death.

(1) drawbar

(2) front hitch receiver

M55O120a

6. improper use of the draw-bar, even

if correctly positioned, can cause a

rear overturn.

7. do not overload an attachment

or towed equipment. use proper

counterweights to maintain tractor

stability. hitch heavy loads to the

draw-bar only.

M55O117a

TF110(RX7320)ROPS합본-US,EU,AU-01.6 6

2016-06-07 오후 7:06:54

Summary of Contents for Kioti RX6020







































































































































































































































































Search results

Summary of Contents for Kioti RX6020

Reviews:

Daedong Kioti RX6020, Manual, Page: 18 / 262

Search results

Summary of Contents for Kioti RX6020

Reviews: